Description Of Symbols; General Safety - Silverline 245014 Manual Del Usuario

GB

Description of Symbols

The rating plate on your tool may show symbols. These represent
important information about the product or instructions on its use.
Wear hearing protection.
Wear eye protection.
Wear breathing protection.
Wear head protection.
Wear hand protection.
Read instruction Manual.
Specification
Max operating pressure............................145 psi
Air inlet/outlet ...........................................
Air consumption ......................................4-6 CFM
As part of our ongoing product development, specifications of
Silverline products may alter without notice.

General Safety

Carefully read and understand this manual and any label attached to
the tool before use. Keep these instructions with the product for future
reference. Ensure all persons who use this product are fully acquainted
with this manual.
Even when used as prescribed it is not possible to eliminate all residual
risk factors. Use with caution. If you are at all unsure of the correct and
safe manner in which to use this tool, do not attempt to use it.
Keep guards in position
• Always keep guards in position, in good working order, correctly
adjusted and aligned. Never attempt to use a tool if any of the supplied
guards are missing. If any guards are damaged, replace before use.
Remove adjusting keys
• Always check to see that keys and adjusting devices are removed from
the tool before use.
Clean the work area
• Accidents can occur where benches and work areas are cluttered or
dirty, floors must be kept clear, avoid working where the floor is slippery.
If working outdoors, make yourself aware of all potential slip and trip
hazards before using this tool.
Children and pets
• Children and pets should always be kept at a safe distance from your
work area. Lock tools away where children can't get access to them.
Do not allow children, or untrained persons to use this tool.
Use the correct tool
• Do not force, or attempt to use a tool for a purpose it was not
designed.
• This tool is not intended for industrial use.
Wear suitable clothing and footwear
• Do not wear loose fitting clothing, neckties, jewellery, or other items
which may become caught. Wear non slip footwear, or footwear with
protective toe caps where appropriate. Long hair should be covered or
tied back.
Keep your balance
• Do not over reach, keep proper footing at all times, do not use tools
when standing on an unstable surface.
4
⁄ " BSP
1
4
Accessories
• The use of any attachment or accessory other than those mentioned
in this manual could result in damage or injury. The use of improper
accessories could be dangerous, and may invalidate your warranty.
Never stand on your tool
• Standing on your tool or its stand could cause serious injury if the tool
is tipped, or collapses. Do not store materials above or near the tool so
that it is necessary to stand on the tool or its stand to reach them.
Secure work
• Where possible, always secure work. If appropriate use a clamp or vice,
it will allow you to use both hands to operate your tool.
Check for damaged or missing parts
• Before each use, check if any part of the tool is damaged or missing,
check carefully that it will operate properly and perform its intended
function. Check alignment of moving parts for binding. Any guard or
other part that is damaged should be immediately repaired or replaced
by an authorised service centre. Do not use if defective.
Air Tool Safety
Dangerous environment
• Always ensure that there is adequate clear space around the work
area. Only use spraying tools in a well ventilated area, or a specialist
spray booth.
• Be aware that air hoses can present a trip hazard, always lay hoses in a
way that minimises hazards.
Protect yourself from vibration
• Hand held air tools may produce vibration. Vibration can cause disease.
Gloves to keep the operator warm may help to maintain good blood
circulation in the fingers. Hand held tools should not be used for long
periods without a break.
Maintain your air tool
• Ensure that you keep air tools clean and lubricated. Lubrication is
essential to prevent corrosion of internal parts, which could lead to
machine failure.
Always disconnect
• Always ensure that your air tool has fully stopped functioning before
putting it down.
• Disconnect any air tool from the air supply before performing any
servicing, or changing any blades, discs, or other attachments.
• Ensure that any blades, discs, or attachments, are correctly fitted before
reconnecting to air supply.
• Always make sure that your air tool is switched OFF before connecting
to air supply.
• Be aware that air tools may hold residual pressure after use. Always
bleed air pressure from the tool after shutting off air supply.
Use the correct air hose
• Use lightweight hoses from the tool to the wall, or compressor coupling.
• Most air tools should be fitted with a coil hose, only use a straight hose
with spray guns.
• When spraying, ensure that the gun is connected to a clean, filtered,
air supply.
Protect your eyes
• Always wear safety goggles, or safety glasses.
Protect your hearing
• Always wear ear protection.
• Do not abuse the machine.
• Do not overload the machine. Allowing the machine to work at its
optimum speed prolongs life, and is more efficient.
• Do not increase air pressure above the recommended level, excessive
pressure leads to wear of moving parts and possible failure. It can also
cause the machine casing to split.
• Do not attempt to modify air tools. Any attempt to modify your tool will
invalidate its warranty and could result in serious injury to you, or those
around you.