Electricity Supply - spot 3900-230 Manual Del Usuario

Thank you for choosing this JBDC product; please read this instruction manual carefully before installing and using the
product, and keep in a safe place for future reference.
This product has been designed to carry out the following operations in a car body workshop:
Dent pulling; welding of nails, rivets, rings and pins; removal of bumps and dents; sheet stretching. It is not designed
for the assembly of metal parts. This device is delivered with an earth clamp, a gun (with cable), a consumables and
accessories box, and an H07RNF mains cable.

ELECTRICITY SUPPLY

- SPOT 3900-230V / 2600 / 2700 / PRO 230: single phase supply 230V 50Hz. 16A Circuit breaker curve D 16 A (aM
type or C curve for 2600).
- SPOT 3900-400V / PRO 400 : Two phase supply 400V 50Hz. Use of PH 1 (1), PH 2 (2) and EARTH (PE). (FIG I Page
2) 16A Circuit breaker curve D 16 A fuse aM type.
NB: If the product trips the circuit breaker, please check that the correct fuse and an adequate circuit
breaker are being used.
• These are A-class devices. They are designed to be used in an industrial or professional environment.
In a different environment, it can be difficult to ensure electromagnetic compatibility, due to
conducted disturbances as well as radiation.
• From 1st December 2010, the new standard EN 60974-10 will be appliable: Warning: these materials
do not comply with IEC 61000-3-12. If they are to be connected to a low-voltage main supply, it is
the responsibility of the user to ensure they can be connected. If necessary consult the operator of
your electrical distribution system
OPERATING AND SETTING (FIG III-PAGE 2)
A- SPOT 3900-230V / 3900-400V / PRO 400 / PRO 230
Connect the machine to an approprate power supply
Connect the gun with its connector.
Nb: and has, in addition to the power connector, a connector to command the torch trigger:
Connect the latter if you wish to start by using the trigger.
-
Disconnect it if you prefer use the generator with automatic start (see OPERATION
-
section).
Press the « on/off » key (⑥).
The indicators switch on for few seconds then the machine displays:
①
•
Tool, n°1 by default, (star welding or dent pulling clamp).
②
•
Power level, n°5 by default, (setting adapted for 0.8mm steel sheets).
To change the power level, press the
automatically.
The available power levels allow the straightening of sheets of varying thickness (fig IV-
To change the tool used with the gun, press the tool selection key (
The tool indicator will blink for 5 seconds. During this time, it is possible to change the tool number by pressing
③
the + or - keys (
Available Tools (fig IV-
Straightening using the star hammer,
1
or dent pulling clamp.
2
Crimped welding wire or rings for straightening
3
Impact reduction with specific copper tip
4
Carbon electrode for tempering
SPOT 2600 / 2700
Connect the machine to an appropriate power supply,
To start the equipment, turn on the potentiometer. Put the potentiometer on "O" for standby mode. (
Select the start mode using the potentiometer:
- Range 6 (left): star or ring welding for sheet stretching.
- Range 7 (top): corrugated wire welding, ideal for curved areas.
- Range 8 (right): Dent pulling work with the adapted copper tip.
or keys (
).
Ⓑ
)
③
). Keep the desired key pressed to scroll through the levels
④
).
5
Welding rivets for side rods
6
Welding rings for fixing vehicle body.
7
Welding studs for vehicle body and connecting beams
7
Ⓐ
).
⑥
).