Canon X Mark I Keypad RF Instrucciones De Configuración Inicial

Radio Frequency
Calculator Keypad /
Teclado Calculadora
Radio Frecuencia
USER GUIDE /
GUIA DE USARIO
E-IM-2522
PRINTED IN CHINA / IMPRESO EN CHINA
IMPORTANT: READ BEFORE USE
ENGLISH
Please read the following instructions and safety
precautions before using the Calculator Keypad.
Keep this sheet on hand for future reference.
THIS DEVICE IS WINDOWS AND MACINTOSH COMPATIBLE.
Be sure to plug in the Radio Frequency (RF) dongle before connecting
the Calculator Keypad to your computer.
INITIAL SETUP INSTRUCTIONS
Set-up may vary slightly depending on the computer.
Instructions provided should work universally on
Windows ® XP, Windows Vista ® , Windows ® 7, and Macintosh.
BATTERY INSTALLATION
1. Remove the battery cover from the back of the Calculator Keypad by sliding
the cover in the direction of the arrow.
2. Install AAA alkaline batteries, matching the positive (+) and negative (–) ends
of each battery with the polarity indicators inside the battery compartment.
3. Place the battery cover back on the battery compartment.
CAUTION: There is a risk of explosion if an incorrect battery type is installed.
Please dispose of used batteries according to their instructions.
PLUG IN THE RF DONGLE
Remove the RF dongle from the
1
storage compartment.
Press the key.
2
NOTE: The icon on
the front display should
press
the key again.
Plug in the RF Dongle into an
3
active USB port on your computer.
NOTE: The
when successfully connected.
Your computer is now setup to
4
use your Calculator Keypad.
RADIO FREQUENCY ICON
 The Radio Frequency icon ( )
will on and off during the setup
connection process.
 Once the device is successfully
connected to your computer, the
Radio Frequency icon ( ) on the
front display will remain solid.
KEY INDEX
▪ Power on
▪ Clear all display | Keypad lock / unlock
WAKE
▪ Re-connect the RF connection
UP
▪ Clear last input entered | Clear all input (CAL mode only)
▪ Escape the input (KP mode only)
▪ Switch between Calculator Mode or Keypad Mode
▪ Backspace in Keypad mode; in Calculator mode shifts each digit of the
displayed numerical value and clears the last digit
▪ Send calculation results or display contents to computer
(CAL mode with RF Connection)
▪ Perform percentage add-on and discount calculation. (CAL mode only)
▪ Execute calculation (CAL mode only)
▪ Enter Key -- the input (KP mode only)
▪ Set the number of digits displayed in calculation after the decimal point
▪ Press and then press and hold , the display will change in the
sequence of F 0 2 3 F (CAL mode only)
▪ F represents a decimal point
CALCULATOR MODE AND KEYPAD MODE
When RF connected, this Calculator Keypad has 2 modes --
Calculator Mode (CAL) and Keypad Mode (KP).
Switch between Calculator and Keypad Mode
 To switch between Calculator and Keypad mode,
simply press the key.
Keypad mode display
Calculator Mode (with RF connection)
 The calculator performs normal 10-digit calculator operations.
 Send calculation results or display contents to a computer by pressing
• You cannot perform a send operation while the E (Error) indicator is shown on
the Calculator Keypad display.
• The key is disabled when the calculator is not RF connected.
SEND
Keypad Mode (with RF connection)
 Input the following to a computer directly:
–
Numbers 0-9 + × ÷
Auto Power Off and Wake-up
 Calculator Only, NO RF Connection
• The device will automatically power off after approximately 7 minutes
of inactivity.
Press the key to turn on the device.
 CAL and KP Modes, with RF Connection
• The RF connection will be disconnected after approximately 30 minutes of
inactivity (the display will reset to "0"). The device will function the same as
"Calculator Only, NO RF Connection".
Press to re-activate the RF connection.
• After the RF connection is disconnected, the device will automatically power
off after an additional 7 minutes of inactivity. Press and then
on the device and re-activate the RF connection.
Power-low Indicator
 When the display is dim or the icon appears,
RF connection will not function. Replace the batteries to
avoid running out of power unexpectedly.
Power-low display
Keypad Lock (with RF connection)
 Press the key and hold for 3 seconds to lock.
 To unlock, press the key and hold for 3 seconds.
Keypad locked display
USAGE TIPS
● When using the calculator with a computer, remove the dongle from the
computer and replace it in the slot on the back of the device.
● When using with a different computer, please connect again with the initial setup.
● The RF icon will remain on (solid, not when the Calculator Keypad is
successfully connected to your computer.
● RF connection requires battery power to function properly.
● When RF connection is off, calculator functions can be used without batteries
(powered by solar panel).
HANDLING AND CARE
● Never continue to use the Calculator Keypad if it starts to smoke, emits a strange
odor, or emits heat. Continued use of the calculator under such conditions creates
the danger of and electric shock.
● When cleaning the Calculator Keypad, do not use a damp cloth or volatile liquid
such as paint thinner; instead, use only a soft, dry cloth.
● Never dispose of the Calculator Keypad improperly (such as burning), which can
lead to personal injury or harm. You should dispose of this product in accordance
with Federal, State, and Local regulations.
TROUBLESHOOTING
If the Calculator Keypad is not connected or not functioning properly:
● Check battery placement direction.
● Make sure computer meets the system requirements described.
● Make sure the RF dongle is plugged into to the computer's USB port and is
functioning properly.
● Remove obstacles between personal computer and the Calculator Keypad.
● If the RF connection is lost and the dongle is plugged into the computer's USB
port, press the key to re-connect.
● If recently connected with a different computer, reset the connection to your current
computer by removing the RF dongle and repeating the initial setup.
● If the display disappears after the RF connection is established, press
check if the icon appears.
● Change to new batteries if the icon appears.
● If the "E" icon appears, the keypad is locked. Press
resume operation. (The "E" icon occurs when the result or memory content
exceeds 10 digits to the left or when dividing by "0".)
 Electromagnetic interference or electrostatic discharge may
cause the display to malfunction. Should this occur, use the tip
of a ball point pen (or similar object) to press the [RESET]
button on the back of the Calculator Keypad.
BATTERY CAUTION !
● Keep the batteries out of reach of children.
● Never expose batteries to high temperatures, direct heat, or dispose by incineration.
● Do not mix new and old batteries or batteries of different types.
● Do not allow metal objects to touch the battery terminals on the device; they can
become hot and cause burns.
● Remove the batteries if they are worn out or have been stored for an extended
period of time.
● Always remove old, weak, or worn out batteries promptly and recycle or dispose of
.
SEND
them in accordance with Federal, State, and Local regulations.
● If a battery leaks, remove all batteries, taking care to keep the leaked
touching your skin or clothes. If from the battery comes into contact with skin
or clothes, skin with water immediately.
SYSTEM REQUIREMENTS
Hardware : Windows based PC x86 / x64 or above, Intel-based Mac
Operating Windows ® XP (SP2 or above) or Windows Vista
®
System : Mac OS X 10.4 ~ 10.6
DEVICE SPECIFICATIONS
Model : X Mark I Keypad RF
Power Source : AAA-size Alkaline batteries x 2
Operating Temperature : 0ºC to 40ºC (30ºF to 104ºF)
Dimension : 155mm (L) x 86mm (W) x 20mm (H)
1-7/64" (L) x 3-25/64" (A) x 25/32" (A)
Weight : 140g (4.9 oz) without batteries / 163g (5.7 oz) with batteries
RADIO FREQUENCY SPECIFICATIONS
to turn
Frequency : 2.4 GHz frequency range
Connection Range : The operating range is up to 10 meters (32.8 feet)
NOTE : Connection range is affected by many factors, such as nearby metallic
objects and the relative positioning of the device and the receiver.
FCC REGULATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
WARNING: Changes or to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• or relocate the receiving antenna, Reorient
• the separation between the equipment and receiver, Increase
• the equipment into an outlet on a circuit different from that to which the receiver is Connect
connected,
• the dealer or an experienced radio/TV technician for help. Consult
Do not make any changes or to the equipment unless otherwise
manual. If such changes or should be made, you could be required to stop operation
of the equipment.
Canon U.S.A., Inc.,
One Canon Plaza, Lake Success, New York, NY 11042, USA
Phone : (516) 328-5000
key and
or to clear and
from
® or Windows ® 7
in the