Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Aculux 4" FMA5-SC Flush Mount Adapter for wood, stone, tile,
and other solid ceilings
These adapters are for use only with Aculux 4" round aperture fixtures using flush-mount trims.
FMA5-SC087 is for use with 1/2" thick to 7/8" thick ceilings.
FMA5-SC125 is for use with 7/8" thick to 1-1/4" thick ceilings.
FMA5-SC163 is for use with 1-1/4" thick to 1-5/8" thick ceilings.
Note: Aculux thick ceiling adapters are not required when using FMA5-SC adapters.
Note: Aculux housings require vertical adjustment of the aiming mechanism to ensure maximum performance at various ceiling
thicknesses. The aiming mechanism can be set for 1/2" thru 1-1/2" ceiling thicknesses with 1/8" increments before or after housing
installation. This adjustment must be set for proper retention of the trims.
To adjust (refer to Fig. 1):
1. Loosen thumb nuts (A) on both sides of the aiming mechanism.
2. Flex left and right trim retainer/height adjustment brackets (B)
inward to disengage aiming mechanism.
3. Raise or lower aiming mechanism until indicators point to the
corresponding ceiling thickness (C). If ceiling thickness is
unknown, measure from housing to ceiling surface (D) and
subtract 1/8" from this measurement. Set aiming mechanism
height at this value.
4. Allow trim retainer/height adjustment brackets to flex back
towards original position, locking height.
5. Tighten thumb nuts loosened in step 1.
Trim Spring Height Adjustment
In some applications, trim spring height adjustment is required.
If ceiling thickness is 1-5/8" to 1-3/4", one spacer per trim spring
is required. If ceiling thickness is 1-3/4" to 2" two spacers per
trim spring are required. (Spacers are shipped with thick
ceiling adapters)
To install (refer to figure 2):
Remove and discard screws holding trim spring assemblies in
place. Install spacer(s) and trim spring assemblies as shown with
provided hardware.
INSTALLATION INSTRUCTIONS
Figure 1
Figure 2
©2016 Acuity Brands Lighting, Inc.
SPRING
ASSEMBLY
SPACERS
Rev 6/16
P5516
pg 1 of 2
Publicidad
Manuales relacionados para Aculux FMA5-SC087
Resumen de contenidos para Aculux FMA5-SC087
- Página 1 Note: Aculux thick ceiling adapters are not required when using FMA5-SC adapters. Note: Aculux housings require vertical adjustment of the aiming mechanism to ensure maximum performance at various ceiling thicknesses. The aiming mechanism can be set for 1/2" thru 1-1/2" ceiling thicknesses with 1/8" increments before or after housing installation.
-
Página 2: Installation Instructions
INSTALLATION INSTRUCTIONS Figure 3 FMA5-SC Installation: 1. Install Aculux housing per the instruction sheet shipped with the recessed housing. Install ceiling with a precise cutout measuring exactly 5.250" diameter (The bottom surface of flush mount adapter can be used as a template). - Página 3 Estos adaptadores son para usarse únicamente con accesorios Aculux de abertura redonda de 4" usando bordes de montaje a ras. FMA5-SC087 es para usarse en techos con un grosor desde 1/2" hasta 7/8".
- Página 4 INSTRUCCIONES DE INSTALACIÓN Figura 3 Instalación FMA5-SC: 1. Instale la carcasa Aculux según las instrucciones enviadas con la carcasa empotrada. Instale el techo con un corte preciso con un diámetro de 5.250" (Se puede usar la superficie inferior del adaptador de montaje a ras como una plantilla).
- Página 5 Ces adaptateurs ne doivent être utilisés qu'avec des luminaires Aculux à ouvertures rondes de 4 po dotés de garnitures affleurantes. Le FMA5-SC087 est réservé aux plafonds de 12,7 à 22,2 mm (1/2 à 7/8 po) d'épaisseur.
- Página 6 INSTRUCTIONS D'INSTALLATION Figure 3 Installation de FMA5-SC: 1. Installez le boîtier Aculux selon les instructions accompagnant le boîtier encastré. Installez le plafond avec une découpe mesurant exactement 133,3 mm (5,250 po) de diamètre (la surface inférieure de l'adaptateur à monture affleurante peut servir de gabarit).