Cadet BRF12 Instrucciones De Instalación

(Front)
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons,
including the following: Read all instructions before using this heater and receptacle.
WARNING
Turn the electrical power off at the electrical panel board (circuit breaker or fuse box) and lock or tag the panel
board door to prevent someone from turning on power while you are working on the heater. Failure to do so could
result in serious electrical shock, burns, or possible death.
STEP 1
Remove one of the wiring compartment covers at either end of the
baseboard heater. Note: if the heater has a built-in thermostat, use
wiring compartment at opposite end.
STEP 2
Remove the slotted knockout closest to the supply wires and install
a strain relief connector. (DO NOT CONNECT TO HEATER WIRES.)
STEP 3
Pull supply wires through the connector and secure, leaving 6 inch
wire leads. Remove 3/4 inch of the insulation from the conductors.
STEP 4
Wrap ground (bare wire) securely around the green terminal screw.
Tighten terminal screw securely, 9-12 pound inch (1.0-1.4 Nm)
of torque. (See Figure 1)
STEP 5
Wrap neutral (white wire) securely around the silver terminal screw.
Tighten terminal screw securely, 9-12 pound inch (1.0-1.4 Nm)
of torque. (See Figure 1)
STEP 6
Wrap hot (black wire) securely around the brass terminal screw.
Tighten terminal screw securely, 9-12 pound inch (1.0-1.4 Nm) of
torque. (See Figure 1)
For more effective and safer operation and to prolong the life of the heater, read the Owner's Guide and follow the instructions. Failure to properly maintain
the heater will void any warranty and may cause the heater to function improperly.
LIMITED ONE-YEAR WARRANTY: Cadet will repair or replace any Cadet
product, including thermostats, found to be defective within one year after the
date of purchase.
These warranties do not apply:
1. Damage occurs to the product through improper installation or incorrect
supply voltage;
2. Damage occurs to the product through improper maintenance, misuse,
abuse, accident, or alteration;
3. The use of unauthorized accessories or unauthorized components constitutes
an alteration and voids all warranties. Refer to Cadet website or call customer
service at 855.CADET.US for list of authorized accessories and components.
4. CADET'S WARRANTY IS LIMITED TO REPAIR OR REPLACEMENT.
5. IN THE EVENT CADET ELECTS TO REPLACE ANY PART OF YOUR CA-
DET PRODUCT, THE REPLACEMENT PARTS ARE SUBJECT TO THE
SAME WARRANTIES AS THE PRODUCT. THE INSTALLATION OF RE-
PLACEMENT PARTS DOES NOT MODIFY OR EXTEND THE UNDERLYING
WARRANTIES. REPLACEMENT OR REPAIR OF ANY CADET PRODUCT
OR PART DOES NOT CREATE ANY NEW WARRANTIES.
cadetheat.com Tel: 855.CADET.US
(Back)
IMPORTANT INSTRUCTIONS
INSTALLATION INSTRUCTIONS
WARRANTY
SAVE THESE INSTRUCTIONS
P.O. Box 1675 Vancouver, WA 98668-1675
BRF12 Baseboard Heater 120V
Receptacle Installation Instructions
http://cadetheat.com/products/baseboard-heaters/baseboard
Since an electrical outlet may not be installed above a heater
(National Electric Code), you may use a Cadet BRF12 outlet in either
end of the Cadet Electric Baseboard to meet local building codes.
TOOLS REQUIRED
• #2 Phillips Screwdriver
• Straight Screwdriver
• (1) Strain Relief Connector
• Wire Strippers
Read all instructions and safety information.
All electrical work and materials must comply with the National Elec-
tric Code (NEC), the Occupational Safety and Health Act (OSHA),
and all state and local codes.
STEP 7
Carefully tuck all wires into wiring compartment and attach
receptacle to the baseboard heater.
STEP 8
Turn the power on at the circuit breaker or fuse box.
SILVER SCREW
GREEN
SCREW
BRASS
SCREW
Figure 1
If you believe your Cadet product is defective, please contact Cadet
during the warranty period, for instructions on how to have the repair or
replacement processed.
Parts and Service
Visit cadetheat.com/parts-service for information on where to obtain parts
and service.
Reduce-Reuse-Recycle
This product is made primarily of recyclable materials. You can
reduce your carbon footprint by recycling this product at the end
of its useful life. Contact your local recycling support center for
further recycling instructions.
©2016 Cadet Printed in U.S.A. 11/16 #720043
Note: A separate 120V circuit and
wiring is required for this product.
DO NOT connect to heater wiring.
Caution: Use copper conductors;
14AWG to 10AWG
CONNECT
GROUND
(BARE WIRE)
CONNECT
NEUTRAL
(WHITE WIRE)
CONNECT HOT
(BLACK WIRE)
(Separate 120V Supply)