Publicidad
Enlaces rápidos
AUTOMOTIVE PRODUCTS, INC.
STEP BAR ASSEMBLIES
ENSAMBLES DE ESTRIBOS
MONTAGES DE MARCHE-PIEDS
25-3480
25-3485
26-3480
ITEM
QTY
1,2
2
STEP BAR, PASSENGER (1) AND DRIVER (2)
3
2
PASSENGER BRACKET
4
2
DRIVER BRACKET
5
12
M8-1.25 X 30MM HEX HEAD BOLT
6
12
3/8" FLAT WASHER
7
12
3/8" LOCK WASHER
8
8
3/8-16 X 1.00" BUTTON HEAD CAP BOLT
9
8
3/8" INTERNAL TOOTH LOCK WASHER
10
8
SPACER WASHER
1,2
2
ESTRIBOS, ACOMPAÑANTE
3
2
SOPORTE DEL LADO DEL ACOMPAÑANTE
4
2
SOPORTE DEL LADO DEL CONDUCTOR
5
12
PERNOS CON CABEZA HEXAGONAL DE M8-1,25 X 30MM
6
12
ARANDELAS PLANAS DE 3/8"
7
12
ARANDELAS DE PRESIÓN DE 3/8"
8
8
PERNO TERMINAL DE 3/8-16 X 1
9
8
ARANDELA DE PRESIÓN DE DENTADO INTERIOR DE 3/8"
10
8
ARANDELAS SEPARADORAS
1,2
2
MARCHE-PIEDS, PASSAGER
3
2
SUPPORT COTE PASSAGER
4
2
SUPPORT COTE
5
12
BOULON A TETE HEXAGONALE DE
6
12
RONDELLE PLATE DE 3/8 PO
7
12
RONDELLE A FREIM DE 3/8 PO
8
8
BOULON A TETE RONDE 3/8-16 X 1,00 PO
9
8
RONDELLE A FREIN A DENTS INTERIEURES 3/8 PO
10
8
RONDELLE D'ESPACEMENT
STEP 1.
Remove the contents from box and check for damage. Verify all parts are present. Read instructions com-
pletely before beginning.
STEP 2.
Remove underbody splash guards from vehicle. Each splash guard is held in place with three bolts and four
push type fasteners.
STEP 3.
Determine passenger and driver brackets. Install drivers side brackets as shown.
STEP 4.
Attach driver side step bar to cradles with the
to rear of vehicle. Secure with 3/8" button head bolts and internal tooth lock washers as shown.
FIGURE 2
.
STEP 5.
Make sure step bar and brackets are properly aligned with vehicle and tighten fasteners.
spacer washers have been included to help level brackets if necessary depending on vehicle tolerances.
Recommended torque values are 19 Ft. Lbs. for 3/8" fasteners and 23 Ft. Lbs. for 8mm fasteners.
STEP 6.
It is recommended to re-install splash guards. Splash guards will have to have a slit cut in the outer edge in
order for the brackets to pass through.
STEP 7.
Repeat installation for passenger side.
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION: 2007-08 HONDA CRV
APLICACIÓN:
APPLICATION: HONDA CRV 2007-08
2
DRIVER SIDE
LADO DEL CONDUCTOR
COTE CONDUCTEUR
CONTENTS -
CONTENIDO
(1)
Y CONDUCTOR
(1)
ET
CONDUCTEUR (2)
CONDUCTEUR
M8-1,25 X 30MM
HONDA CRV
, MOD. 2007-08
PASSENGER SIDE
LADO DEL ACOMPAÑANTE
1
COTE PASSAGER
- CONTENU
(2)
Westin
logo facing outward. Step pad closer to end of tube goes
3
TOOLS -
HERRAMIENTA
10MM" SOCKET
13MM SOCKET
7/32" HEX WRENCH
RATCHET
RATCHET EXTENSION
SMALL FLAT HEAD SCREWDRIVER
TORQUE WRENCH
UTILITY KNIFE
DADO DE 10MM"
DADO DE 13MM
LLAVE HEXAGONALE DE 7/32"
MANERAL
EXTENSIÓN PARA MANERAL
DESTORNILLADOR DE PUNTA PLANA
PEQUEÑO
LLAVE DE TORQUE
NAVAJA
DOUILLE 10MM
DOUILLE 13MM
CLE HEXAGONALE 7/32 PO
CLIQUET
EXTENSIÓN PARA CLIQUET
PETIT TOURNEVIS A BOUT PLAT
CLE DE COUPLE
COUTEAU
SEE FIGURE 1.
WO:
75-0864 REVISION 11/16/07
4
- OUTILS
SEE
NOTE:
Four extra
Publicidad
Manuales relacionados para Westin 25-3480
Resumen de contenidos para Westin 25-3480
- Página 1 , MOD. 2007-08 APPLICATION: HONDA CRV 2007-08 AUTOMOTIVE PRODUCTS, INC. STEP BAR ASSEMBLIES PASSENGER SIDE LADO DEL ACOMPAÑANTE ENSAMBLES DE ESTRIBOS COTE PASSAGER MONTAGES DE MARCHE-PIEDS 25-3480 25-3485 26-3480 DRIVER SIDE LADO DEL CONDUCTOR COTE CONDUCTEUR ITEM CONTENTS - CONTENIDO...
- Página 2 FINISH PROTECTION Westin products have a high quality finish that must be cared for like any other exposed finish on the vehicle. Protect the finish with a non-abrasive automotive wax, (e.g. Pure Carnauba) on a regular basis. The use of any soap, polish or wax that contains an abrasive is detrimental, as the compounds scratch the finish and open it to corrosion.
- Página 3 DE TUERCA EN TUBO FIGURE 2 STEP BAR ATTACHMENT FIGURA 2 ACCESORIO DE ESTRIBO FIGURE 2 FIXATION DU MARCHE-PIEDS Thank You for choosing Westin products Westin Automotive Products, Inc. For additional installation assistance please call 5200 N. Irwindale Ave. Suite 220 Irwindale, Ca.