Before Assembly - Palram FERIA 3x3.05 Manual De Instrucciones

EN
Please read these instructions carefully before you start to
assemble this product.
Please carry out the steps in the order set out in these instructions.
Keep these instructions in a safe place for future reference.
When encountering the information icon, please refer to the relevant
assembly step for additional comments and assistance.
This icon indicates that the installer should be inside the product.
Safety
• Some parts may have sharp edges. Please be careful when handling components.
• Always wear gloves, eye protection, and long sleeves when assembling or performing
any maintenance on your product.
• To prevent injuries, do not allow children to play under the product during assembly.

Before Assembly

• This product is suitable for Palram's Patio Covers range
• It is highly recommended to be assisted by a second person in some steps.
• Sort the parts and check according to the contents parts list.
• Prior to the installation, some parts of the Patio cover need to be
dismanteld, it is recommend to keep them in a safe place for future use.
• Periodically check the kit's components to assure that it remains stable.
• Note: Use only the parts registered in the content list, which are compatible
with your Patio Cover›s gutter (7999 & 8119), some parts may be surplus.
During Assembly
In case that you already own Palram Patio cover it is necessary to
dismantle parts as described in Step 1 in the kit assembly manual.
Steps:
Step 2: To assemble the rear profile please refer to the patio cover assembly manual at the stage of
"holes marking" as:
Feria Tuscany Olympia
3x3 - Step 7 3x3 - Step 7 3x3 - Step 5
3x4.25 - Step 6 3x4.25 - Step 9 3x4.25 - Step 7
3x5.46 - Step 9 3x5.46 - Step 9 3x5.46 - Step 7
4x4.25 - Step 12 -
For fixation to the wall, return to step 2.
Step 3: connect part 8303 (drawings a,b) and than return to the patio cover assembly manual as follow:
Feria Tuscany Olympia
3x3 - Step 8 3x3 - Step 8 3x3 - Step 6
3x4.25 - Step 13 3x4.25 - Step 13 3x4.25 - Step 11
3x5.46 -Step 13 3x5.46 - Step 13 3x5.46 - Step 11 3x4.25 - Step 9 3x5.46 - Step 10
4x4.25 -Step 16 -
After completion, perform drawing c at this step.
Step 4: In all relevant patio cover sizes, you may choose either of these 2 assembly options:
Option 1 (Steps 4+5+6+9+10+11+12) - assembling all posts supplied.
Option 2 (Steps 4+7+8+9+10+11+12) - Whenever you are using this EZ Link Kit you may give up using
one leg.
Step 6 (Option 1) : make sure the distance between the post and the connection point does not exceed
60 cm / 23.6 inch. The Maximum distance between the posts may not exceed 120 cm / 47.2 inch.
Step 10: before performing this stage, return to the patio cover assembly manual at the stage of
"assembling the roof system" as follow:
Feria Tuscany Olympia
3x3 - Step 15 3x3 - Step 14 3x3 -Step 11
3x4.25 - Step 22 3x4.25 - Step 20 3x4.25 - Step 17
3x5.46 - Step 21 3x5.46 - 20 Step 3x5.46 -Step 17 3x4.25 -Step 15 3x5.46 -Step 17
4x4.25 - Step 26 -
Step 12: Tightening the bolts is done from the inner part. Spread silicone follow the connection (a,b).
Pay attention: while installing the kit, alignment with original patio cover is important.
Tighten all screws when completing assembly.
Sierra Joya
All sizes All sizes
Step 5 Step 6
-
Sierra Joya
2.3x2.3 - Step 7 3x3 - Step 7
3x3 - Step 6 3x4.25 - Step 10 3x4.25 - Step 9
-
- 3x5.46 - Step 9
Sierra Joya
2.3x2.3 - Step 12 3x3 - Step 13
3x3 - Step 11 3x4.25 - Step 17 3x4.25 - Step 16
- 3x5.46 - Step 15 -
Carnival
3x3 - Step 6
3x4.25 - Step 5
-
-
Carnival
3x3 - Step 10
-
-
Carnival
3x3 - Step 18
-
-