Battery Change - Comsafe VISION Manual De Instrucciones

GU GU
OPERATION MANUAL FOR VISION OPERATION MANUAL FOR VISION
!!ATTENTION:
Please read these instructions b e f o r e operating the
lock or set a new combination. We decline any responsibility for malfunctions
due to improper switching or use of force or inappropriate treatment, or for
property or material damage which may be due, for example, to incorrect safe
locking.
Your safe model "Vision" can be opened with a master
code or a guest code or one of the two emergency keys
provided.
Each keystroke is confi rmed by an acoustic signal.
Each keystroke can be corrected by pressing "*".
If you want that code entered (master or user code)
not be displayed, before entering the code, press "*".
Instead of the pressed digit, the screen displays "-".
Non-alkaline battery use is not recommended.
The safe is delivered with the default master code 0-0-0-0-0-0 and user code
1-6-8-0; for safety reasons, we recommend you to immediately change the
master code and the user code with a personal code.
1. COMMISSIONING:
a. Remove the emergency locking system cover to the right of the keyboard
by sliding to the right.
b. Enter one of the two emergency key supplied with the notch in the lock.
c. Turn the key clockwise.
d. Open the door.
e. Turn the key back to the starting position and remove it.
f. Remove the screw securing the battery compartment on the inside of the
door.
g. Slide the battery cover to the left.
h. Introduce four 1.5 volt batteries (pay attention to the correct polarity)
AA (alkaline).
i. The display shows "HELLO" - the safe is now operational.
j. Close the battery compartment.
2. INCORRECT ENTRY
When entering an incorrect code and after pressing "#" key, a fi ve
times beep is heard and the display shows "ERROR 1"; for another
incorrect input the screen displays "ERROR 2" and after three incorrect entries
appear the message "ERROR 3".
3. LOCKOUT PERIOD AFTER INCORRECT
ENTRY
If the code is entered incorrectly three times, the screen displays ''HOLd05''
and a fi ve minutes lockout period commences. During this fi ve minutes lockout
period, a new entry is not possible. If during lockout period, the electronic lock
is activated and a key is pressed, the display shows "HOLd05" and the remai-
ning time is counted until expiration. This lockout period can not be stopped,
not even by removing batteries.

4. BATTERY CHANGE

opening is not possible, so that batteries should be immediately changed).
a. If necessary, open the safe using the emergency key (see point 9
- Open the emergency key).
b. Remove the screw securing the battery compartment on the inside of the
door.
c. Slide the battery cover to the left.
d. Remove old batteries.
e. Install new batteries (alkaline) - Note the correct polarity.
f. Close the battery compartment by pushing the battery cover to the right
Vision.indd 5
(Display is poor or cannot be read or
and tighten it.
ATTENTION:
after battery change, the stored codes (master code, user
code) are maintained.
5. MASTER CODE CHANGE
is maintained after a battery change)
a. Tap the screen in the middle, the display shows "HELLO".
b. Press "*" twice.
c. The display shows "SUPER".
d. Enter the current master code (default 0-0-0-0-0-0).
e. Press "#" to confi rm.
f. The display shows "CC - -".
g. Enter "0 1" to change the master codes.
h. Press "#" to confi rm.
i. The display shows "NEW".
j. Enter the desired master code (6 digits).
k. Press "#" to confi rm.
l. The display shows the message "rEPEAT".
m. Repeat the desired master code (6 digits).
n. Press "#" to confi rm.
o. If the display shows "GOOD", the master code has been changed successfully.
p. The display shows "CC --"
q. To exit the menu, press the "*".
ATTENTION:
if during programming appears the message "ERROR",
start the procedure from point 5.f.
6. CLOSING - SAVING THE USER CODE
a. Tap the screen in the middle, the display shows "HELLO".
b. Close the door and enter your desired user (four, fi ve or six digits).
c. The display shows the code entered.
d. Confi rm by pressing "#".
e. The safe gets automatically locked and the display shows the message
"CLOSE".
f. After proper closing the display shows the message "Closed" and the
selected code.
g. If proper closing is not possible, the display will show "ERROR".
h. Start again closing as described from point 6.
7. OPENING WITH THE USER CODE
a. With the door closed or pulled bolt, tap in the screen in the middle and the
display will show the message "HELLO", enter your saved user code (four,
fi ve or six digits).
b. Confi rm by pressing "#".
c. During opening, the display shows "OPEN".
d. After opening the display shows "OPENEd".
INFO
To lock again the safe with the previously selected user code, you must press
only "#", with the door closed.
The safe closes as described at point 6-d and can be opened with the previously
selected user code, as described at point 7.
8. OPENING WITH THE MASTER CODE
a. Tap the screen in the middle, the display shows "HELLO".
b. Press "*" twice.
c. The display shows "SUPER".
d. Enter the current master code (default 0-0-0-0-0-0).
e. Press "#" to confi rm.
f. The display shows "CC --".
g. Enter "0 0" to open with the master code.
h. Press "#" to confi rm.
i. During opening, the display shows "OPEN".
(the master code selected by you,
5
27.02.2017 13:21:47