Speedaire 2CUA3 Instrucciones De Operación Y Manual De Partes

Carrete portamangueras industrial 1/4, 3/8"

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Speedaire
Description
Speedaire
®
Industrial Hose Reels have an internal spring for automatic hose
rewind and a locking ratchet to maintain desired hose position while in use.
Unpacking
After unpacking the unit, inspect all components for any damage that may have
occurred in transit. Read the following precautions and instructions before you
begin assembly or using. Failure to comply with these instructions could result in
personal injury or property damage. Keep these instructions in a convenient
location for future reference.
Specifications and Dimensions
Maximum
Operating
Model
Pressure
(PSI)
Hose
Dimensions
2CUA3
300
1/4
2CUA5
300
3/8
2CUA7
300
3/8
General Safety Information
1. Make sure incoming line pressure does
not exceed maximum rated operating
pressure for your model hose reel.
2. Use proper eye protection when
assembling and using the hose reel.
3. Remove all spring tension before
beginning disassembly (Refer to
hose replacement).
4. Keep children away from the work area,
a recoiling hose has surprising force.
5. Never let the hose retract without
holding on to it.
Throughout this manual the following
symbols have these special meanings.
NOTE:
Indicates special instructions which
are important but not related to hazards.
Warns about hazards
that may cause minor personal injury or
property damage if ignored.
Form 5S6557
Industrial Hose Reel 1/4, 3/8"
®
Hose
Hose Reel
Dimensions
Dimensions
Length
Length
Width
(Feet)
(Inch)
50
16.9
35
16.9
50
16.9
that can cause serious personal injury,
death, or major property damage if
ignored.
Installation
Installation of Reel
1. For ceiling mounting: install reel at least
10 feet above the floor.
2. You will need to purchase appropriate
hardware for your specific reel mounting
configuration.
3. The reel base has four 1/2" (12.7mm)
drilled holes for mounting on a suitable
flat surface. Figure 2 on is a
template showing the correct location of
the 4 mounting holes in the base.
4. The reel is supplied with a hose guide
roller bracket. The bracket position may
require repositioning depending on the
selected reel mounting position. Figure
1 below shows "Typical Mounting
Positions". if bracket position needs to
be changed, do the following:
Printed In China
04634
Version 0
Weight
Height
(Pounds)
(Inch)
(Inch)
9.3
19.1
37.4
9.3
19.1
35.2
9.3
19.1
39.6
Warns about hazards
2CUA3/2CUA5/2CUA7
Hose Outlet
Reel Inlet
Connection
Connection
NPT Male
NPT Female
(Inch)
(Inch)
1/4
3/8
1/4
3/8
1/4
1/2
(a) Pull out some hose and let reel latch.
(b) Remove the bolts that attach the
guide roller bracket to the support
post.
(c) Rotate hose guide roller bracket to
correct position, replace bolts and
tighten.
5. Using all four holes in the base,
mount the reel in the desired
location. Be sure to use appropriate
hardware (not included), and tighten
securely.
6. Apply pipe sealant to threads on reel
supply line, attach line to reel inlet and
tighten.
Only use flexible hose
to connect reel inlet. Do not use rigid
plumbing.
7. Apply pipe sealant to outlet fitting of
hose, then attach to desired tool, nozzle,
or quick connect fitting.
8. Use soapy water to check connection for
leakage, also check hose reel for correct
operation, (Refer to - Operation
Section).
ICM017
04/01
Maximum
Operating
Temperatures
(Fahrenheit)
210
210
210

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Speedaire 2CUA3

  • Página 1 2CUA3/2CUA5/2CUA7 Speedaire Industrial Hose Reel 1/4, 3/8" ® Description Speedaire ® Industrial Hose Reels have an internal spring for automatic hose rewind and a locking ratchet to maintain desired hose position while in use. Unpacking After unpacking the unit, inspect all components for any damage that may have occurred in transit.
  • Página 2: Maintenance And Repair

    LIMITED ONE YEAR WARRANTY release pressure in hose. 4. Periodically check the hose condition for Should a Speedaire Hose Reel fail to 2. Securely stabilize the reel by mounting wear or damage and check the swivel perform satisfactorily due to defect or poor or clamping to work surface.
  • Página 3 24 hours a day - 365 days a year Please provide the following: -Model Number -Serial Number (if any) -Part description and number as shown on parts list Repair Parts List for Speedaire® Industrial Hose Reel 1/4, 3/8” No. de Ref. Description Kit Components...
  • Página 4 2CUA3/2CUA5/2CUA7 Manufactured for Dayton Electric Mfg. Co. Niles, Illinois 60714 U.S.A.
  • Página 5 Por favor, guarde las instrucciones para futura referencia. Carrete Portamangueras Industrial 1/4, 3/8" Descripción Speedaire® Carretes Portamangueras Industriales tienen un resorte interno para rebobinado de manguera automático, y un trinquete de bloqueo para mantener la posición deseada de manguera mientras está en uso.
  • Página 6: Operación

    2CUA3/2CUA5/2CUA7 Speedaire® Instrucciones de Operación y Manual de Partes Carrete Portamangueras Industrial 1/4, 3/8" 8. Use agua jabonosa para comprobar FIGURA 1 Posiciones de Montaje del Carrete fugas en la conexión, así como el carrete portamangueras para su correcto funcionamiento, (véase la Sección de Operación).
  • Página 7 Sírvase proporcionar lo siguiente: -Número de Modelo -Número Serial (si aplica) -Descripción y número de parte según se muestre en la lista de partes Repair Parts List for Speedaire® Industrial Hose Reel 1/4, 3/8” No. de No. de Descripción Kit de Componentes...
  • Página 8 2CUA3/2CUA5/2CUA7 Speedaire® Instrucciones de Operación y Manual de Partes Fabricado para Dayton Electric Mfg. Co. Niles, Illinois 60714 EE.UU. 4-Sp...
  • Página 9 Conservez s'il vous plaît ces instructions pour la référence future. Bobine de Tuyau Industrielle1/4, 3/8" Description Les Bobines de Tuyau Industrielles Speedaire® ont un ressort interne pour le rebobinage de tuyau automatique et un cliquet de verrouillage pour maintenir la position de tuyau désirable lors l'utilisation.
  • Página 10: Maintenance Et Réparation

    2CUA3/2CUA5/2CUA7 Speedaire® Mode d'emploi et Manuel de Pièces de Rechange Carrete Portamangueras Industrial 1/4, 3/8" l'adaptation de connexion rapide FIGURE 1 Positions de Montage de Bobine désirés. 8. Utilisez l'eau savonneuse pour vérifier la connexion pour la fuite, vérifier aussi la bobine de tuyau pour l'opération...
  • Página 11 -Référence -Numéro de série (si besoin) -Description et numéro de pièce de rechange indiquées dans la liste des pieces de rechange Liste des Pièces de Rechange Speedaire® Industrial Hose Reel 1/4, 3/8” No. de No. de Descripción Kit de Componentes...
  • Página 12 2CUA3/2CUA5/2CUA7 Speedaire® Mode d'emploi et Manuel de Pièces de Rechange Fabriqué Pour Dayton Electric Mfg. Co. Niles, Illinois 60714 États-Unis 4-Fr...

Este manual también es adecuado para:

2cua52cua7

Tabla de contenido