Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Palmgren Operating Manual & Parts List
SAFETY RULES (CONTINUED)
• Disconnect tool from power when changing accessories such
as grinding wheels, buffing wheels and the like.
• Avoid accidental start-up. Make sure that the switch is in the
OFF position before plugging in.
• Do not force tool. It will work most efficiently at the rate for
which it was designed.
• Keep hands away from moving parts and grinding surfaces.
• Never leave a tool running unattended. Turn the power off and
do not leave tool until it comes to a complete stop.
• Do not overreach. Keep proper footing and balance.
• Never stand on tool. Serious injury could occur if tool is tipped
over.
• Know your tool. Learn the tool's operation, application and spe-
cific limitations.
• Use recommended accessories. Understand and obey all safety
instructions supplied with accessories. The use of improper
accessories may cause risk of injury to persons.
• Do not over tighten wheel nut. Replace cracked wheel immedi-
ately. Use only flanges supplied with the grinder.
• Adjust distance between wheel and tool rest to maintain
less gap.
• Handle the workpiece correctly. Whenever possible, use tool
rest to support workpiece during grinding operation. Turn tool
off if it jams.
• Always use guards and eyeshields.
• Clean grinding dust from beneath tool frequently.
ASSEMBLY
Parts to be fastened to the unit should be located and accounted
for (See List and Figure 1).
IMPORTANT: Do not attempt assembly if parts are missing. Use
this manual to order replacement parts.
A
3
/
-16 x
3
/
" Hex bolt, 4 each
8
4
B
3
/
" Flat washer, 6 each
8
C Tool rest bracket (left & right), 2 each
D Tool rest (left & right), 2 each
E
5
/
" Flat washer, 2 each
16
F
5
/
-18 x 1" Knob, 2 each
16
G #10-24 x
1
⁄
" Pan head screw, 4 each
2
H Upper eyeshield bracket (left & right), 2 each
I
Eyeshield, 2 each
J Lower eyeshield bracket, 2 each
K
3
⁄
" Lock washer, 2 each
8
L
1
⁄
-20 x
3
⁄
" Knob, 2 each
4
8
M Spark guard (left & right), 2 each
N
3
/
-16 x
1
⁄
" Knob, 2 each
8
2
Dust collector hose (not shown).
TOOL REST ASSEMBLY
• Place tool rest (D) over tool rest bracket and secure in position
with
5
/
" flat washer (E) and
16
• Attach tool rest bracket to the bottom of the left wheel guard
using two
⁄
-16 x
⁄
" hex head bolts (A) and two
3
3
8
4
ers (B). Tighten bolts finger tight.
• Position tool rest so that distance between tool rest and grind-
ing wheel is less than
1
/
" . Reposition angle of tool rest if neces-
16
sary. Secure all knobs and bolts.
• Mount right tool rest in a similar manner.
5
⁄
-18 x 1" knob (F).
16
⁄
" flat wash-
3
8
EYESHIELD ASSEMBLY
• Attach spark guard (M) to left wheel guard using
knob (N),
3
⁄
" flat washer (B) and
8
• Mount left upper eyeshield bracket (H) to eyeshield (I) using
two #10-24 x
bracket.
NOTE: Left upper eyeshield bracket is stamped "L" for identification.
• Slide
1
/
-20 x
3
4
(M) into upper upper eyeshield bracket (H) and secure in
position.
• Locate eyeshield in desired position for protecting operator
and secure all knobs and bolts.
• Mount right eyeshield assembly in a similar manner.
G
1
/
" or
16
D
Figure 1 –Left Tool Rest and Eyeshield Assembly
DUST COLLECTOR HOSE
• A dust collector hose has been provided with grinder. Slide
hoses onto sides of T-connector and flanges. Mount the hose
by sliding the flanges at each end over the exhaust ports on
the left and right wheel guards. Attach 2½" shop vacuum hose
to collector hose. Be sure hose is mounted securely.
DANGER:
Be sure to empty shop vacuum of all flammable materi-
al (flammable liquids and vapors, paper, wood, plastic, etc.) before
connecting vacuum to grinder. Hot sparks from grinder may ignite
flammable materials in shop vacuum.
MOUNT GRINDER
• Mount grinder to a solid horizontal surface (hardware not pro-
vided). If mounted to metal pedestal, align mounting holes
with corresponding holes in pedestal. Insert a
head bolt with flat washer through base of grinder. From bot-
tom of pedestal, place a
the bolt. Tighten only until space between grinder base and
pedestal is
1
/
8
against the first to prevent loosening by vibration.
• To mount grinder to wooden bench top, use
screws with flat washers beneath heads. Tighten screws until
space between grinder base and bench top is
3
3
/
" lock washer (K).
8
⁄
" pan head screws (G) and lower eyeshield
1
2
/
" knob (L) through hole at top of left spark guard
8
I
H
M
B
C
B
E
F
INSTALLATION
1
/
" flat washer and
4
" . Using second nut on each bolt, jam tighten
82066 & 82086
3
⁄
-16 x
1
⁄
"
8
2
J
L
K
N
A
1
/
-20 x 1¼" hex
4
1
/
"-20 hex nut onto
4
1
/
x 1¼" wood
4
1
/
" .
8
Publicidad
Tabla de contenido
