Bpt XAS/301 Instrucciones De Instalación

NOTE: This equipment has been tested and found to com-
ply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential instal-
lation.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
P5
M2
L N
DL1
DL2
SW6
DIMENSIONS IN MILLIMETRES
DIMENSIONES EN MILIMETROS
03.2009/2409-6901
SW10
SW
SW7
B OUT
SW8
– X
SW9
ON
OFF
P6 M3
M1
SW5
SW3
SW2 SW4
SW1
A
210 43,5
7,5 57
B
210 64,5
XAS/301 US
BPT S.p.A.
Via Cornia, 1
33079 Sesto al Reghena-PN-Italy
info@bpt.it – www.bpt.it
INSTALLATION
EN
INSTRUCTIONS
XAS/301 POWER
SUPPLIER-REPEATER
Unit repeating audio, video and
+
UP
data signals for main X2, X1 lines.
Enables system 300, X2, X1systems to
be extended in terms of distances and
number of receivers. Besides, the
power supplier XAS/301 is able to pro-
vide power to receivers directly from
BUS X1 (B OUT).
The unit, created with a 12-unit modu-
le for installation on DIN rail, features 9
jumpers: SW1, SW2, SW3 for com-
pensating the incoming line, SW4,
SW5 for compensating the entire
length, SW7, SW8, SW9 for compen-
sating the total outgoing line.
In addition, it features two indicator
LEDs for checking data transfer.
1
Main functions
- Connection of max. 200 handsets.
- Connection of max. 100 monitors of
which only 1 is active.
- Connection of 2 signal boosters
XDV/300A in installations X1.
- Compensation of incoming and out-
going line capacity up to 1 km.
- Automatic compensation of inco-
ming video line up to -26 dB.
- Serial connection of up to 2
XAS/301 units.
- Parallel connection of up to 50
XAS/301 units in installations system
300, 25 XAS/301 if connected after an
entry panel X2.
Function of each terminal (fig. 1)
Terminal block M2
L
mains
N
2
Terminal block M1
B IN (X1) X2 line input
Terminal block M3
X1 line output (20 VDC)
B OUT
intermittent 0.8A/0.2 A 1'/3'
+
XUP not used
–
Line length configuration
WARNING. When calculating distan-
ces, you must also allow for the num-
ber of distributors and shunts con-
nected (Tab.1)
Distributors
Shunts
XDV/304
3
Tab. 1
• Compensation of total line X1 con-
nected on line B IN terminal block M1
(the unit comes supplied with all jum-
pers set to OFF) (Tab. 2)
Total
length
150 m
150÷350 m
350÷650 m
650÷1.000 m
= OFF
Tab. 2
• Compensation of line X1 between
control unit XA/300LR or X2-series
entry panel and last receiver or next
XAS/301 (the unit comes supplied with
jumper SW4 set to ON) (Tab. 3)
Total
length
0÷250 m
250÷500 m
= OFF
Tab. 3
• Compensation of total line B OUT
connected on line B OUT terminal
block M3 (the unit comes supplied
with all jumpers set to OFF) (Tab. 4)
Total
length
150 m
150÷350 m
350÷650 m
650÷1000 m
= OFF
Tab. 4
Function of jumper SW10
(Disabling the video)
The unit has a jumper SW10 (fig. 1) for
disabling the video.
Function of LEDs DL1 and DL2
DL1: comes on whilst data are being
sent towards receivers (B OUT). E.g.:
call, system enabling etc..
DL2: comes on whilst data are being
sent towards control unit XA/300LR or
X2 entry panel (B IN).
E.g.: door lock release, auxiliary,
audio communication commands
etc.
Function of potentiometers P5 and
P6
The unit features 2 potentiometers
(factory set) for adjusting volume,
where necessary.
P5: adjusts volume heard at entry
panel.
P6: adjusts volume heard through
receivers.
Erasing device data stored in
memory
Should the unit be reused in a different
position or in an installation other than
that where it was first installed, all data
Equivalent line
length previously stored in its memory must
be erased.
50 m
Do this by removing and refitting jum-
per SW6 (LEDs DL1 and DL2 will light
SW1 SW2 SW3
= ON
SW4 SW5
= ON
SW7 SW8 SW9
= ON
1