Intimus 2051 SmartFold Instrucciones De Uso página 8

Setting a Paper Size
To change paper sizes, press the "SIZE SELECT" button
located on the operator interface. You must specify the
paper size that you intend to fold prior to running the
folder.
Setting the Paper Guides
If your paper size is different than the factory set paper size, adjust
the Paper Guides to the desired size. To adjust the paper guides,
loosen the thumb knobs of the Paper Guides located under the
Feed Table. Move the Paper Guides to the desired location, and
then retighten the thumb knobs.
Do not over-tighten the thumb knobs!
Setting a Fold Type
To change the fold type, press the "FOLD SELECT" button
located on the folder keypad. Once you have selected a
fold type, the folder will wait for 8 seconds for any additional
settings that you may want to set, such as a quantity of
folds to run.
Running a Test Fold
Pressing the TEST button once will feed and fold one sheet
of paper and then stop.
Fold Skew Adjustment
With the Feed Table depressed into the
load position, push or pull the adjust-
ment lever located in the Feed Table
until the desired amount of skew adjust-
ment has been made.
Ready to Fold
Pressing the RUN button will initiate folding. Folding will
continue until one of the follow conditions is met: 1.) the
Stop button is pressed, 2.) the Feed Table becomes empty
of paper, 3.) a folding error is encountered, or 4.) the pro-
grammed quantity reaches 0 (zero).
Stopping the Folder
If the folder is running, pressing the STOP button once per-
forms a normal shut down, allowing all paper to clear the
machine prior to the main motor stopping. Pressing the
STOP button twice in quick succession causes an immedi-
ate stop of the main motor. This is to be used for emergency stops
only.
Folding Multiple Sheets
Insert up to 4 sheets of 20# Bond
paper through the Multi-sheet Bypass.
The sheets may be stapled together.
To fold multiple sheets together at the
same time, place all of the sheets into
the Multi-Sheet Bypass. For best
results, insure that all of the pages
are aligned with each other. Insert
stapled edge first.
Adjusting and Counting
Incremental Adjustment Buttons
This button will increase a number value by one count.
This button will decrease a number value by one count.
Fold Table Adjustment
2nd Fold
Table
1st Fold
Table
Incremental Adjust Buttons, you will see the indicators on the
corresponding fold table move. The fold tables can be positioned
to a specific location by entering the value through the number
buttons.
Stack Wheel Position
To adjust the position of the Stack Wheels, press the Stack
Wheel button (shown on the left), and then press either the
increase or decrease button. The correct position of the
Stack Wheels is automatically calculated based on the length
of the paper and the position of the fold tables. Manual adjustment is
not normally required when performing a standard, pre-programmed
fold.
Folder Speed
To adjust the speed of your folder, press the Speed button
and then press either the increase or decrease button
(Incremental Adjustment Buttons). Folder speed can be
adjusted while the folder is running. For most folding jobs,
the folder can be run at full speed (100%). Typically, the only time
that the folder is run less than 100% is when folding light weight
paper (less than 20#) or if the paper has a glossy or silky smooth
finish.
Display Contrast
To adjust the display contrast of the LCD display, press the
Display Contrast button (shown on the left), and then press
either the increase or decrease button (Incremental
Adjustment Buttons).
Quantity and Batch Mode
The Quantity (#) is used to specify the total number of
sheets to be folded, and to specify a Batch quantity.
Quantity
To program a specific number of pages to be folded, press the
Quantity (#) button. Using the numbers on the keypad, enter the
quantity of sheets to fold, and press the enter key. Pressing the
Enter key while in the Quantity screen will automatically place you
into the Batch Mode screen.
Batch Mode
The Batch Mode function automatically places a gap between batch-
Insert paper
es. To enable Batch Mode, enter a Batch quantity value greater than
here
0 (zero). This quantity is the number of sheets to be folded. When
this quantity of sheets has been folded, the folder will suspend feeding
until the Exit Conveyor has become clear of paper, then will resume
folding. This fold/pause/fold sequence will continue until one of the
following conditions is met: 1.) the Stop button is pressed, 2.) the
Feed Table becomes empty of paper, 3.) a folding error is encoun-
tered, or 4.) the programmed quantity reaches 0 (zero).
To enter the Batch Mode, you must press the Quantity (#) button and
press the Enter button from the Quantity screen. To specify a differ-
ent Batch quantity, using the number buttons, enter a value between
0 (zero) and 250, and then press the Enter button to save this value.
To fine adjust one of the fold tables, press the
corresponding fold table adjustment button, and
then press either the increase or decrease but-
ton (Incremental Adjustment Buttons). After you
have pressed one of the fold table buttons as
you repeatedly press, or hold down one of the
(7)