camry Premium CR 4410 Manual De Uso página 5

5. Press the Auto Single Cup button (1) to let the hot water out to wash the coffee filter (18).
6. Repeat steps 3, 4, 5 above.
7. Empty condensation from water and coffee from the removable drip tray (7).
How to make espresso coffee?
Connect the device to the power supply and press the power button (3). At this moment the indicator light (19) flashes blue, wait until it
stops flashing, then the device will finish heating and will be ready for use.
1. While the device is preheating, you can put the ground coffee powder (you should use the fine powder, not too thick or too thin) into
the ground coffee filter (18). For one espresso cup use one measurement spoon (14) of your favorite ground coffee. For two espresso
cup use 1,5 measurement spoon (14) of your favorite ground coffee. Then use the measuring spoon handle (14) to press it tightly; at the
same time wipe the coffee powder on the edge of the filter (18). You can use the filter (24) suitable for 2 cups ground coffee capacity too.
2. Insert the ground coffee filled filter (18) into the filter housing (17), keep it by filter handle (15). Fit filter with ground coffee under the
unlock mark (21), then move it the right side to lock it, just under the lock mark (22), then place the coffee cup (or 2 cups) under the
funnel (20).
3. Adjust the position of the coffee cup (or 2 cups at the same time), let the coffee flow along the cup wall.
4. Press:
- the Auto Single Cup button (1), you will hear di-di sound, then it starts to flow out a coffee to your cup. Coffee stops flow out
automatically, you will hear di-di-di-di-di sound. Single coffee is around 100ml capacity.
- the Auto Double Cup button (2), you will hear di-di sound, then it starts to flow out the coffee to 2 cups at the same time. Coffee stops
flow out automatically, you will hear di-di-di-di-di sound.
- the Manual Coffee Cup button (4) button to flow out coffee as long as you like. After the quantity of coffee will be your desired level,
press the Manual Coffee Cup button (4) again to stop flow out of coffee. Do not leave the appliance unattended, it may overflow coffee.
5. Wait a minute for coffee dripping and the coffee is ready.
Steam foaming function
1. Press the Steam button (5), the light indicator (19) will turn red and it will flashing, when the red light changes from blinking to
continuous red light, the preheating is complete.
2. The amount of steam can be adjusted according to the individual's proficiency. Before froth the milk foam, you should release the
water in the steam nozzle (13). It is recommended to pour the milk into the 1/3 high of the pitcher, insert the steam nozzle (13) into the
milk at 1cm depth, and then slowly unscrew the steam knob (10) until steam starts to eject. You can sway the pitcher a little, but do not
contact the bottom of the pitcher with the steam nozzle (13).
3. When the temperature of milk reaches about 75 degrees of Celsius and the milk foam begins to expand, turn the steam knob (10) to
"OFF" position, turn off the steam button (5) to make the light indicator (19) turns blue, press the power button (3) directly to turn off the
device.
After the milk foam is completed, clean the milk on the surface of the steam nozzle with a damp cloth in time and spray the steam to
prevent the milk from drying out and blocking the vent.
How to make cappuccino coffee?
1. Prepare bigger volume cups suitable to cappuccino coffee.
2. Prepare coffee according to points 1-5 described in part: How to make espresso coffee?
3. Prepare the milk foam according to points 1-3 described in part: Steam foaming function.
4. Then shake the pitcher on the table so that the milk foam is fully blended and pour it into the cup with coffee.
Hot water function
1. Pressing the power button (3).
2. The device starts to preheat, at this time, the light indicator (19) flashes blue; when the blue light stops blinking and turns on
continuous blue lighting, the warm-up is completed, it takes about 2 minutes.
3. Stand up the cup under the steam nozzle (13).
4. Turn the steam knob (10) until the steam nozzle (13) flowing out hot water. Knob should exceed the position of hot water function mark
(23).
5. Press:
- the Auto Single Cup button (1), you will hear di-di sound, then it starts to flow out hot water – around 150ml - to your cup. Water stops
flow out automatically, you will hear di-di-di-di-di sound. If you have to stop water flow out immediately press the Auto Single Cup button
(1) again.
- the Auto Double Cup button (2), you will hear di-di sound, then it starts to flow out the water – around 250 ml - to your cup. Water
stops flow out automatically, you will hear di-di-di-di-di sound. If you have to stop water flow out immediately press the Auto Double Cup
button (2) again.
- the Manual Coffee Cup button (4) button to flow out hot water as long as need. Do not leave the device without control. After the
quantity of hot water will be your desired level, press the Manual Coffee Cup button (4) again to stop flow out of hot water. If you have to
stop water flow out immediately press the Manual Coffee Cup button (4) again.
6. When finished, turn off the Steam knob (10), then press the power button (3) off .
7. The hot water can be used for drinking, cleaning or heating cups before pouring your coffee.
5