Publicidad
10
Ingresso pulsante pedonale, apre parzialmente il
11
cancello(per circa 7 sec.) contatto N.O.
10
Ingresso pulsante START se premuto durante la
12
fase di apertura ferma la manovra,durante la
chiusura inverte il movimento.Contatto N.O.
10
Ingresso pulsante STOP se premuto ferma
13
qualunque manovra e annulla la richiusura
automaticaContatto N.C.
26
Uscita secondo canale radio, contatto N.O. pulito (portata, vedi caratteristiche del ricevitore)
27
6.
Collaudo
Da eseguire con il cancello a metà della sua corsa e solo dopo aver installato tutti i dispositivi di sicurezza previsti dalle
normative vigenti al fine di ridurre al minimo ogni rischio
•
Verificare il corretto collegamento del motore tenendo presente che la prima manovra che la scheda esegue una volta alimentata
è un apertura se questo non avviene invertire i collegamenti ai morsetti 6-7
•
Verificare il corretto funzionamento dei finecorsa movendo manualmente la leva e controllando che si spenga il led corrispondente
in caso contrario invertire i collegamenti ai morsetti 17-18
•
Verificare il corretto funzionamento di tutti i dispositivi di sicurezza installati al fine di ridurre al minimo ogni eventuale rischio.
•
Istruire il personale addetto all'uso dell'automazione sui relativi comandi, dispositivi di sicurezza e pericolosità derivante dall'uso
dell'automazione.
•
Compilare il fascicolo tecnico ed adempiere agli eventuali obblighi derivanti dalle normative vigenti.
GB
1.
Safety rules
Warning: Any repairing, fitting or adjustment made from people not qualified is strictly forbidden and in order to avoid any possible
accident, all necessary precautions must been taken (ex: switch off the power supply as well as disconnect batteries). Daspi is not
responsible for possible damages or injuries to people, objects or animals caused by any unauthorized modification of product. Do not
install this product into an explosive place
Keep scrupulously this booklet and include it into the main user manual in a suitable place well known by all the interested people.
2.
Model
The control panel MACH6E has been designed for driving 1 operator for sliding gates mod. BIG FOOT and it has an electric clutch
and electronic brake. Daspi is not responsible for any different use of control panel MACH6E
3.
Main components
F1
Power supply fuse10A
F2
Control fuse 2A
F3
Flashing light fuse 2A
SW1
Dip-switch for the control panel programming
Led showing the control panel's connections (to be checked after turning on the power supply)
DL1
It shows the manoeuvre of the gate (1 flashing/sec. while opening, fix light with the gate completely open, 2 flashing/sec. while
closing)
DL2
Always off, it turns on with control PED(pedestrian) DL5
DL3
Always off, it turns on with control START
DL4
Always on, it turns off with control STOP
Check again the connections and the devices if the above led don't correspond.
4.
Control panel programming and set up
The programming of dip switches must be made with control panel switched off
SW1
1
It sets the automatic shutting, adjustable by trimmer BREAK
It doesn't accept any other control START while opening
2
(residential system)
3
Pre-flashing of 2 seconds before any movement
It sets the feature "close immediately" (trimmer BREAK must be
more than 0) working only while opening.
With the dip residential system ON, if photocells detect
something , as soon as the gate open completely it closes
4
immediately, only if the photocells are freed.
With the dip residential system OFF, if photocells detect
something , as soon as the entrance is freed, the gate starts
closing after 2 seconds.
Separate entrances OPEN - CLOSE:
5
the entrance START becomes OPEN and the entrance PED
(pedestrian) becomes CLOSE.
Photocells working while opening. As soon as they are freed,
6
the gate keep opening.
20
21
22
23
24
25
JP1
JP2
JP3
J1
DL6
DL7
DL8
ON
Uscita 24Vac per alimentare i dispositivi esterni come le
fotocellule
Uscita spia cancello aperto(22=+24Vdc 23=gnd massimo
30mA) segue il funzionamento del led DL1
Ingresso antenna collegare al morsetto 25 il polo caldo
dell'antenna e al morsetto 24 la calza dell'antenna
Terminal for power supply connection 230 Vca 50 Hz
Terminal for connecting the motor, the light and 2° capacitor
Terminal for connecting the safety and control devices
Radio receiver connector
Always on, it turns off with control PHOTOCELLS
Always on, it turns off with control SEFETY DEVICE
Always on, it turns off with control LIMIT SWITCH OPENING
Always on, it turns off with control LIMIT SWITCH CLOSING
Automatic shutting off.
Control START is accepted while the gate is opening. Gate
stops.
Pre-flashing off
"Close immediately" off
Normal working
Photocells working only while closing. If they detect
something, the gate stops and re-opens.
OFF
3
Publicidad
