Publicidad
Enlaces rápidos
AUTOMOTIVE PRODUCTS, INC.
BULL BAR ASSEMBLY
ENSAMBLE DE PARRILLA
DELANTERA CON TIRÓN
LA BULL BAR
32-1360
32-1365
ITEM
QTY
1
1
BULL BAR ASSEMBLY
2,3
2
BRACKET, PASSENGER (2) AND DRIVER (3)
4
2
PLASTIC PLUG
5
4
RUBBER BUMPER
6
2
1/2-13 X 2.00" HEX HEAD BOLT
7
2
1/2" FLAT WASHER
8
2
1/2" LOCK WASHER
9
2
M12-1.25 X 30MM HEX HEAD BOLT, YELLOW ZINC
10
2
1/2" FLAT WASHER, YELLOW ZINC
11
2
1/2" LOCK WASHER, YELLOW ZINC
1
1
ENSAMBLE DE PARRILLA DELANTERA CON TIRÓN
2,3
2
SOPORTE, ACOMPAÑANTE
4
2
TAPONES DE PLÁSTICO
5
4
PARACHOQUES DE HULE
6
2
PERNOS CON CABEZA HEXAGONAL DE 1/2-13 X 2,00"
7
2
ARANDELAS PLANAS DE 1/2"
8
2
ARANDELAS DE PRESIÓN DE 1/2"
9
2
PERNOS CON CABEZA HEXAGONAL DE M12-1,25 X 30MM, ZINC AMARILLO
10
2
ARANDELAS PLANAS DE 1/2", ZINC AMARILLO
11
2
ARANDELAS DE PRESIÓN DE 1/2", ZINC AMARILLO
1
1
LA BULL BAR
2,3
2
SUPPORTS, PASSAGER (2) ET CONDUCTEUR (3)
4
2
BOUCHON DE PLASTIQUE
5
4
PARE-CHOCS EN CAOUTCHOUC
6
2
BOULONS A TETE HEXAGONALE 1/2-13 X 2,00 PO
7
2
RONDELLES PLATES 1/2 PO
8
2
RONDELLES PLATES 1/2 PO
9
2
BOULONS A TETE HEXAGONALE M12-1,25 X 30MM
10
2
RONDELLES A FREIN 1/2 PO, ZINC JAUNE
11
2
RONDELLES PLATES 1/2 PO
STEP 1.
Remove the contents from box and check for damage. Verify all parts are present. Read instructions
completely before beginning.
stainless steel fasteners.
STEP 2.
NOTE:
It may be necessary to remove/relocate front license plate and license plate bracket. It is not
required, but strongly recommended. If local/state laws requires a license plate, license plate relocation kit
32-0055 is available.
STEP 3.
Determine passenger and driver brackets.
hook. Save shorter 12mm fasteners. Attach brackets using shorter existing fasteners and supplied 12mm
bolts as shown. Leave loose.
STEP 4.
Attach Bull Bar to mount brackets using 1/2" stainless steel fasteners. Level and adjust Bull Bar as desired and
tighten all fasteners.
fasteners and 55 Ft. Lbs. for 12mm fasteners.
LIGHT INSTALLATION:
Insert threaded stud on base of the light through hole in cross tube. Using a ratchet, extension
and socket for correct size of nut supplied, insert through large clearance hole in bottom of cross tube.
Thread nut and washers on stud and tighten.
best to get the nut started.
NOTE:
Fits most 6" round or rectangle lights. Some lights may require replacing included mount/isolator with rubber
bumpers provided. Mounting stud of 1/2" or less required. Plug mount holes with caps provided if not
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION: 1999-06 TOYOTA TUNDRA
APLICACIÓN: TOYOTA TUNDRA, MOD. 1999-06
APPLICATION: TOYOTA TUNDRA 1999-06
1
CONTENTS -
CONTENIDO
(2)
Y EL CONDUCTOR
, ZINC JAUNE
NOTE:
Westin advises the installer to use a thread lubricant on all of the
SEE FIGURE 2.
Recommended torque values are 37 Ft. Lbs. for 1/2" stainless steel
2001-07 TOYOTA SEQUOIA
TOYOTA SEQUOIA, MOD. 2001-07
TOYOTA SEQUOIA 2001-07
- CONTENU
(3)
, ZINC JAUNE
SEE FIGURE 1.
Remove and discard tie down loop and tow
SEE FIGURE 2. NOTE:
WO:
2
TOOLS -
HERRAMIENTA
17MM SOCKET
3/4" WRENCH
RATCHET
TORQUE WRENCH
DADO DE 17 MM
LLAVE DE TUERCAS DE 3/4"
MANERAL
LLAVE DE TORQUE
DOUILLE 17MM
CLE 3/4 PO
CLIQUET
CLE DE COUPLE
A short socket, not a deep well works
75-0402 REVISION C 3/19/08
3
- OUTILS
Publicidad
Manuales relacionados para Westin 32-1360
Resumen de contenidos para Westin 32-1360
- Página 1 STEP 1. Remove the contents from box and check for damage. Verify all parts are present. Read instructions NOTE: completely before beginning. Westin advises the installer to use a thread lubricant on all of the stainless steel fasteners. STEP 2. NOTE: It may be necessary to remove/relocate front license plate and license plate bracket.
- Página 2 FINISH PROTECTION Westin products have a high quality finish that must be cared for like any other exposed finish on the vehicle. Protect the finish with a non-abrasive automotive wax, (e.g. Pure Carnauba) on a regular basis. The use of any soap, polish or wax that contains an abrasive is detrimental, as the compounds scratch the finish and open it to corrosion.
- Página 3 FIGURA 2 ACCESORIO PARA FARO (NO SE INCLUYEN LOS FAROS) FIGURE 2 FIXATION DU PHARE (PHARES NON INCLUS) Thank You for choosing Westin products Westin Automotive Products, Inc. For additional installation assistance please call 5200 N. Irwindale Ave. Suite 220 Irwindale, Ca.