Du Pont WFFT110 Serie Instrucciones De Instalación

WFFT110_Faucet_instructions
Installation Instructions
Faucet for Filtered Water
Instrucciones de instalación
Grifo para agua filtrada
Before You Begin
B
The Faucet for Filtered Water in this package is designed to fit a 9/16" hole. Most standard sinks come with 1-3/8" or 1-1/2" diameter water sprayer holes that can be used for
mounting the Faucet. If the pre-drilled holes cannot be used or are not in the desired position, a new hole must be drilled using either a 9/16" or 5/8" drill bit to accommodate the
Faucet for Filtered Water. The Faucet for Filtered Water base should be positioned securely on a flat surface with adequate space for proper function. Also consider convenience
and appearance of the Faucet before installation.
1
In order to prevent parts and materials from falling down the drain, line the sink with newspaper or a towel.
2
Apply masking tape to the area to be drilled in order to prevent scratching the sink surface or countertop if the drill bit slips during operation.
3
Using a center punch, mark the drill hole. Use the 1/4" drill bit to make a pilot hole. Then use the 9/16" or 5/8" drill bit to drill the final hole.
Drill completely through the sink or countertop and smooth the rough edges with a file.
4
Consult your local plumbing codes and install accordingly.
C C A A U U T T I I O O N N
Safety glasses and a respirator are
recommended for this process, as it
may produce dust that can cause
severe irritation if it is inhaled or comes
in contact with eyes.
STEP 1
Mount the Faucet
1
Assemble Faucet for Filtered Water Neck
neck into top of Faucet base and tighten retaining nut until snug.
2 D
Guide the Black Rubber Gasket onto the threaded Faucet for Filtered Water
stem. Slip the threaded Faucet for Filtered Water stem into the sink or countertop
hole. Make sure the Faucet for Filtered Water sits flat on top of the sink or
countertop surface.
3
From underneath the sink, slide the Metal Lock Washer
Water stem. Then screw the plastic Faucet Stem Nut
stem until it is flush with the Metal Lock Washer. Screw until it is slightly snug and
check to make sure the faucet spout is in the proper position. Using fingers, tighten
the nut to secure the Faucet for Filtered Water to the sink.
NOTE: Do not tighten the Faucet Stem Nut with pliers as it may strip the Faucet
stem threads.
STEP 2
Install the Kitchen Faucet Adapter
NOTE: The Kitchen Faucet Adapter is designed to fit 1/2" NPTF supply threads.
1
Locate the cold water shut-off valve under the sink. Turn off the cold water supply
to the sink.
NOTE: If uncertain about which line supplies the cold water, turn on the hot water
to the kitchen faucet. Allow the water to heat up and carefully feel the pipes under
the sink. The pipe that remains cool to the touch is the cold water supply.
2
Turn on the cold water on the kitchen sink to release pressure and allow water to
completely drain from the line.
WFFT110 Series
6/27/08 12:06 PM Page 1
Model Series WFFT110
Serie del modelo WFFT110
V.3.0 - 021508
DO NOT DRILL THROUGH AN ALL-PORCELAIN OR CAST IRON SINK. If installing on an all-porcelain or cast iron sink, the faucet must be
mounted in a pre-drilled sprayer hole or through the countertop next to the sink. If the countertop must be drilled, make certain that the
area below the drilling location is free of wiring and pipes. Also, make sure that there is sufficient room to make the proper connections
to the bottom of the faucet mount. DO NOT DRILL THROUGH COUNTER TOPS MORE THAN 1" IN THICKNESS OR COUNTERTOPS MADE
OF TILE, MARBLE, GRANITE OR SIMILAR SUBSTANCE. Consult with a plumber or the countertop manufacturer for assistance.
3
Disconnect the cold water line from the 1/2" threaded stem on the bottom of the
kitchen faucet.
A B
to Faucet for Filtered Water . Insert
4
Connect the Kitchen Faucet Adapter
5
If you have a rigid plumbing pipe, it may be necessary to shorten the pipe. Remove
any burrs with a metal file.
6
Connect the cold water supply line to the Kitchen Faucet Adapter securely.
STEP 3
E
up the Faucet for Filtered
F included) for Water Supply Line from System Head
all the way up the Faucet
Outlet to Faucet for Filtered Water
1
Determine the length of 1/4" plastic tubing (not included) that will be necessary to
connect the System Head Outlet to the threaded Faucet for Filtered Water stem.
Make sure to allow enough plastic tubing to prevent kinking in the line. Cut the 1/4"
plastic tubing squarely on both ends.
2
Wet one end of the 1/4" plastic tubing with water and push it into the System Head
Outlet until it stops.
3
Gently slide the plastic Compression Nut down
Follow with the plastic Ferrule
position with the larger opening on the bottom (going into the nut). Place the
plastic Insert
4
Firmly push the 1/4" plastic tubing into the end of the threaded Faucet for Filtered
Water stem. Hand-tighten the plastic Compression Nut onto the threads. Tighten
with an adjustable wrench approximately 1/2 turn.
NOTE: Do not bend or crimp plastic tubing when inserting. Do not over tighten the
Compression Nut.
A
Faucet for Filtered Water
B
Parts & Hardware Included
A
Faucet for Filtered Water Neck
B
Faucet for Filtered Water
C
Kitchen Faucet Adapter
D
Black Rubber Gasket
E
Metal Lock Washer
F
Faucet Stem Nut
G
Insert
H
Ferrule
I
Compression Nut
Information & Assistance
www.waterfiltration.DuPont.com
Protect Plus, LLC I Hickory, NC 28601 USA
For installations in Massachusetts, the Commonwealth of Massachusetts Plumbing Code CMR248 shall be adhered to.
C C A A U U T T I I O O N N
C
to the kitchen faucet stem.
Install 1/4" Plastic Tubing (not
I
(thread side up) over the tubing.
H
, making sure that the Ferrule is in the proper
G
into the end of the 1/4" plastic tubing.
Package Contents
Faucet for Filtered Water Neck
D
C
Black Rubber Gasket
E
KFA-Kitchen Faucet Adapter
1/2" NPTF to 1/4" Tube
Metal Lock Washer
DuPont Part No. WFAF400
F
Faucet Stem Nut
I Tools & Materials Required
Drill with 1/4" & 9/16" or
I 5/8" Drill Bits
File
I
Adjustable Wrench
I
1/4" Plastic Tubing
I
Utility Knife
I
Pan or Bucket
828-449-1040
For Service Requests & Product Information
Hours of Operation: 24 Hours/Day, 7 Days/Week
1
F
2
4
3
5
HOT WATER
VALVE
X
X
3
I
YOUR
SYSTEM
HERE
Faucet Connector Set
DuPont Part No. WFAF600
G
Insert
H
Ferrule
I
Compression Nut
800-441-7515
For Safety & Health Questions
FAUCET FOR
FILTERED WATER
D
E
KITCHEN FAUCET
2
C
YOUR
SYSTEM
HERE
1
COLD WATER
VALVE
YOUR
SYSTEM
HERE
G
H
YOUR
SYSTEM
HERE
V.3.0 - 021508