Installation Instructions - Knape & Vogt BSC9-1-20 Instrucciones De Instalación

Parts Included
K. Two (2) Slide Brackets
L. Two (2) Door Brackets
M. Four (4) #6-18 x 5/8" Phillips
flat-head sheet metal screws
N. Eight (8) #10-24 x 1/4" Phillips
pan-head machine screws
(Discard 4. Not required.)
O. Four (4) external
tooth-lock washers
(Discard all. Not required.)
L.
K.
Tools Required
• Phillips head screwdriver
• Drill with 1/16" (1.5mm) bit for
drilling pilot holes
• Tape measure or ruler
• Pencil
Product Assemblies
PDMKT
2700 Oak Industrial Drive NE, Grand Rapids, MI 49505 USA
800.253.1561 • 616.459.3311 • www.kv.com
SOFT-CLOSE WASTE BIN
DOOR BRACKET KIT
FOR SOFT-CLOSE SLIDING WASTE BINS

Installation Instructions

Inspect all parts and read all instructions prior to beginning assembly and installation.
IMPORTANT: DISCARD INSTRUCTIONS THAT CAME PACKAGED
1
WITH THE PDMKT DOOR BRACKET KIT AND USE THESE INSTEAD.
Attach Slide Brackets
Note: Proceed only if you are installing the optional door
mount bracket kit. You will need to replace the hardware
pack supplied with your door mount kit that is intended for
mounting the slide brackets to the slides with the door mount
hardware kit supplied with your Bottom Mount Soft-Close unit.
Extend the slide members of the waste bin product assembly
out of the cabinet interior to a comfortable working position.
Select a side to begin assembly. Position the slide bracket on
the inside of the slide member, aligning the holes. Be sure
that the keyhole flange on the slide bracket is facing
outward towards the cabinet sides. For each slide member,
attach the slide bracket to the slide member with 2 - #10-24 x 3/8" machine screws with
star washers (J). Route machine screw (J) through the slide bracket (K), then through the
M.
spacer washer (I) and into the slide nut. Ensure screws are fully tightened. Repeat this
process for attaching the opposite side slide bracket to the slide member.
Locate Vertical Screw Hole Positions
2
N.
If cabinet bottom is flush with the top edge of lower cabinet face frame cross rail,
proceed to Step 2A. If cabinet bottom is below the top edge of lower cabinet face frame
cross rail, proceed to Step 2B.
2A Identify if the cabinet door is hinged to the
cabinet frame. If so, return the sliding members
O.
to the closed position inside the cabinet interior,
and close cabinet door. Select a side to begin
marking locations. Measure the distance of the
cabinet door from the bottom edge of the door
to the top edge of the cabinet face frame lower
rail. This dimension is "Y". Add 2-1/2" to the "Y"
dimension, and this is the vertical location of the
lower hole for attaching the door bracket to the
back of cabinet door. Mark this location with
pencil. Measure 7-1/2" above this location, mark
with pencil. This is the vertical location of the
upper hole for attaching door bracket to back
of cabinet door. Repeat this process for locating holes on other side of cabinet door
frame. IMPORTANT! DO NOT DRILL HOLES AT THIS TIME! If door is hinged to cabinet, remove
hinge cups from cabinet frame and cabinet door. Proceed to Step 3.
Identify if the cabinet door is hinged to the cabinet frame. If so, return the sliding members
2B
to the closed position inside the cabinet interior, and close cabinet door. Select a side to
begin marking locations. Measure the distance of the cabinet door from the bottom edge
of the door to the top edge of the cabinet face
frame lower rail. This dimension is "Y". Identify the
dimension of the cabinet bottom recess. This
dimension is "X". Add 2-1/2" to the "Y" dimension,
then subtract the "X" dimension and this is the
vertical location of the lower hole for attaching
the door bracket to the back of cabinet door.
Mark this location with pencil. Measure 7-1/2"
above this location, mark with pencil. This is the
vertical location of the upper hole for attaching
door bracket to back of cabinet door. Repeat
this process for locating holes on other side of
cabinet door frame. IMPORTANT! DO NOT DRILL
HOLES AT THIS TIME! If door is hinged to cabinet,
remove hinge cups from cabinet frame and
cabinet door. Proceed to Step 3.
J
I
K
CABINET FLOOR FLUSH WITH FRAME
DOOR
7-1/2"
BETWEEN HOLES
Y + 2-1/2"
(LOCATION OF
BOTTOM HOLE)
Y
CABINET FLOOR
CABINET FACE FRAME Y= DOOR OVERLAP
CABNET FLOOR BELOW FRAME
DOOR
7 1/2"
BETWEEN HOLES
X"
Y" + 2-1/2"-X"
(LOCATION OF
LOWER HOLE)
CABINET FLOOR
Y"
Y = DOOR OVERLAP
CABINET FACE FRAME X = DIFFERENCE BETWEEN
FRAME AND FLOOR
1
2A
2B
2