Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75292F
Wrenches: ¾, 7/8, 18mm & 21mm Deep Well Socket
Drill Bits: None
Fasteners Typical
Both Sides
Frame Rail
Spacer Block
Existing Nut
1
Qty. (4)
Hex Bolt ½-13 x 5" GR5
2
Qty. (8)
Flat Washer ½"
3
Qty. (6)
Spacer Block ½ x 1-1/8 x 2-1/2
1.
Loosen (6) bumper bracket nuts, (3) each side. Remove (4) rearmost bolts, (2) each side. Remove remaining flange nut.
DO NOT REMOVE FORWARD BOLT. Return (4) bolts and flange nuts to vehicle owner.
2.
Replace (4) rearmost bolts with new bolts supplied in fastener kit.
3.
Place (1) block flush on each bolt.
4.
Raise hitch into position over the exhaust pipe, being careful not to drop blocks.
5.
Push bolts with flat washers through frame rail, blocks & brackets and attach flat washers, lock washers and nuts to (4)
rearmost bolts (as shown).
6.
Replace the flange nuts on the forward existing bolts.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
z
2005, 2007, 2009 Cequent Performance Products
Installation Instructions
Dodge Durango
Fascia
Forward Existing Bolt
DO NOT REMOVE
Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Tighten all M14 CL10.9 fasteners with torque wrench to 148 Lb.-Ft. 201 N*M)
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV1, SUV2
1
2
3
2
4
5
4
Qty. (4)
Lock Washer ½"
5
Qty. (4)
Hex Nut ½-13
Sheet 1 of 3
75292N
Part Numbers:
75292
44175
70751
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
9000 (4086 Kg.)
900 (409 Kg.)
6000 (2724 Kg.)
600 (272 Kg.)
12-29-09
Form: F205 Rev A 5-6-05
Rev. E
Publicidad
Manuales relacionados para Cequent Performance Products 75292
Resumen de contenidos para Cequent Performance Products 75292
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 75292N 12-29-09 Rev. E 2005, 2007, 2009 Cequent Performance Products Form: F205 Rev A 5-6-05...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 75292N 12-29-09 Rev. E 2005, 2007, 2009 Cequent Performance Products Form: F205 Rev A 5-6-05...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 75292N 12-29-09 Rev. E 2005, 2007, 2009 Cequent Performance Products Form: F205 Rev A 5-6-05...