RS X100 Hoja De Instrucciones

V6265
Accessori (Fig.4) Codice RS 489-778
Nota: Non usare gli accessori oltre i 60Vc.c.; quando si
!
eseguono misurazioni di tensione, non afferrare la
sonda al di là del salvadita.
La gamma di sonde per oscilloscopio non ha parti interne sostituibili.
Non tentare di smontare i prodotti. Non esporre le sonde a solventi o
vapori di solventi in quanto possono danneggiare i componenti interni,
le parti sagomate ed il cavo, le regolazioni di compensazione devono
essere eseguite usando un segnale di prova inferiore a 30V. NON
REGOLARE MAI LA COMPENSAZIONE USANDO LA SONDA SU
CIRCUITI VIVI.
Non usare le sonde oltre i valori di tensione raccomandati.
La RS Components non si assume alcuna responsabilità in merito a perdite di
qualsiasi natura (di qualunque causa e indipendentemente dal fatto che siano dovute
alla negligenza della RS Components), che possono risultare dall'uso delle
informazioni fornite nella documentazione tecnica.
RS Components Ltd
PO Box 99
Corby
Northants
NN17 9RS
UK
RS Components Gmbh
Hessenring 13b,
64546 Mörfelden-Walldorf
Frankfurt
Germany
Radiospares Composants
Rue Norman King, BP 453
60031 Beauvais Cedex
France
RS Components S.p.A.
Via Cadoena 66
20090 Vimodrone Milano
Italy
Issued / Herausgegeben / Publication / Publicado / Pubblicato 09/1998
X100-Oszilloskoptastkopf, fester Anschluß
Instruction Leaflet
Sonda para osciloscopio de cable fijo X100
Bedienungsanleitung
Hojas de instrucciones
Feuille d'instructions
Foglio d'instruzioni
Figures / Abbildung / Figures / Figura
1
C
G
F
A
D
E
B
2
600V
400V
200V
0V
10kHz 100kHz 1MHz 10MHz 100MHz 1GHz
3
4
C
G
F
A
E D
B
A. Earth lead A. Schutzleiter A . Cable de tierra A. Fil de terre A. Cavetto di
B. Grabber B. Abgreif- B. Empuñadura B. Prise massa
C. Trimmer tool klemme C. Herramienta C. Trimmer B. Grabber
para el
D. BNC adaptor C.Abgleich- D. Adaptateur C. Trimmer
condensador de
E. I.C. tip werkzeug BNC D. Adattatore
compensación
F. Insulating tip D.BNC-Adapter E. Bout I.C. E. Puntale C.I.
D. Adaptador BNC
G. Spare E. I.C.-Spitze F. Bout à isolation F. Puntale
E. Punta I.C.
measuring tip F. Isolierspitze G. Bout de mesure isolamento
F. Punta aislante
G.Ersatzprüf- de rechange G. Puntale di
G. Punta de
spitze misura di
medición de
ricambio
repuesto
X100 Fixed Lead Oscilloscope Probe
Sonde d'oscilloscope X100 fixe
Sonda per oscilloscopio X100
ad attenuazione fissa
BS EN61010-1 600V CAT I
Specification guide
Note: These oscilloscope probes are to be used only with
!
oscilloscopes that are permanently attached to
EARTH.
Introduction
Fixed attenuation X100 Oscilloscope probe. Suitable for use with most
general purpose oscilloscopes with bandwidths up to 250MHz. This
oscilloscope probe features a field replaceble probe head and screw-in
probe tip. Each kit includes a full set of accessories and full instruction
leaflet. These oscilloscopes probes have been designed to meet the
requirements of BS EN61010-1 to 300V CATII or 600V CATI and hence
satisfy the 'low voltage directive'. 'CE' mark is applied.
RS part no. ______________________________________489-734
Reference ____________________________________1-1248536-2
Model __________________________________________M15X100
Attenuation__________________________________________100:1
Bandwidth ________________________________________250MHz
Rise time __________________________________________1.4nS
Input cap. __________________________________________6.5pF
Input res. __________________________________________99MΩ
Comp. range ____________________________________15 to 50pF
Maximum input Voltage ________________(Up to altitude of 2000m)
300V dc ____Incl. peak ac category II derating with frequency (fig.2)
600V dc ____Incl. peak ac category I derating with frequency (fig 2)
Maximum operating temperature range ____________-25 to +70°C
Cable length ______________________________________1.20m
Probe compensation (fig 3)
The following adjustment is required whenever the oscilloscope probe
is transferred from one oscilloscope or input channel to another.
Connect the probe to the oscilloscope. Apply a 1kHz square wave
signal to the probe tip and adjust the oscilloscope controls to display a
few cycles of the waveform with an amplitude of approximately 5
divisions, adjust the compensating trimmer to obtain a flat topped
square wave. Please note that adjustment of the X100 probe is made
at the BNC tailbox end of the probe.
V6265
RS Stock No.
489-734