Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

UHF RFID Tag Mounting Instructions
LiftMaster Proprietary RFID Tags must be used with LiftMaster RFID Long
Range Reader (LMSC1000). The tags are high performance radio frequency
identifi cation devices. They have been designed to be installed on the
interior (LMHNTG/SPLMHNTG LiftMaster RFID Hang Tag and LMUNTG/
SPLMUNTG LiftMaster Dual-Purpose RFID Tag [Windshield/Headlamp])
or exterior of the vehicle (LMUNTG/SPLMUNTG LiftMaster Dual-Purpose
RFID Tag [Windshield/Headlamp]). LMUNTG Tag can be installed on
surfaces that are made of glass, plastic or fi berglass. When mounted on
the windshield, these tags are designed to not interfere with the vision of
the driver. Installation of the LMUNTG is critical, as when installed properly
the tags are designed to not interfere or obstruct the headlamp's beam
per United States DOT specifi cations. Additionally, the LMUNTG offers
an unmatched level of security as their design does not allow them to be
removed or transferred once mounted to the vehicle.
All LiftMaster tags have been tested to withstand a variety of environmental
conditions such as UV exposure, vibration, temperature and humidity
cycles. Tags have been engineered for the rigors of automotive use, but
handle carefully during installation process.
NOTE: Please consult your local and state vehicle ordinances to determine
the allowable mounting locations for this type of tag. Due to the wide
variance in windshield design, this document is intended as a general guide
and not inclusive of all vehicle makes and models. This document serves to
supply only general guidelines for the correct handling and installation of
tags.
NOTE: If the facility code is not visible on the tag it will be "000".
Choosing a Proper Tag Mounting Location
For optimum performance, the LMUNTG/SPLMUNTG LiftMaster Dual-Purpose RFID Tag (Windshield/Headlamp) must be installed on a windshield location
or other suitable mounting point that is facing the RFID reader during normal driving. Hang Tags (LMHNTG) should be attached to your rear view mirror for
best results.
Reader
Tag Read
Zone
Preferred Tag
Locations
Correct Driver Side
Reader Placement
NOTE: Use LMHNTG for rear view mirror tag location and LMUNTG for all other tag locations.
Reader
Tag Read
Tag not
Zone
read
Preferred Tag
Locations
Correct Overhead
Reader Placement
LiftMaster Vehicle RFID Tags
LMHNTG Hang Tag and LMUNTG LiftMaster Dual-
Purpose Vehicle RFID Tag (Windshield/Headlamp)
WARNING: This product can expose you to chemicals including
lead, which are known to the State of California to cause cancer or
birth defects or other reproductive harm. For more information go
to www.P65Warnings.ca.gov
LMHNTG
FC: 24
ID: 00025
Remove permit while vehicle is in motion.
LMHNTG/SPLMHNTG*
LiftMaster RFID Hang Tag
*If specifi c Facility Code and Start
ID are required, use special part #s
SPLMHNTG, SPLMUNTG.
Tag not
Tag Read
read
Zone
Correct Passenger Side
Reader Placement
07/18
FC: 24
LMUNTG/SPLMUNTG
LiftMaster Dual-Purpose RFID
Tag (Windshield/Headlamp)
Reader
Preferred Tag
Locations
07/18
FC: 24
ID: 000025
LMUNTG Windshield/Headlamp Tag
ID: 000025

Publicidad

loading

Resumen de contenidos para LiftMaster LMHNTG

  • Página 1 For optimum performance, the LMUNTG/SPLMUNTG LiftMaster Dual-Purpose RFID Tag (Windshield/Headlamp) must be installed on a windshield location or other suitable mounting point that is facing the RFID reader during normal driving. Hang Tags (LMHNTG) should be attached to your rear view mirror for best results.
  • Página 2 2.5" (6.4 cm) from any materials containing metal. This includes the vehicle roof line, side pillars and rearview mirror mounting block. Make sure that the tag is not behind any metallic surface or darkened trim around the window. For LMHNTG, hang from rearview mirror.
  • Página 3 LMUNTG Dual-Purpose Vehicle RFID Tag Headlamp Installation For optimum performance, the RFID tag must be installed on the headlight lens or other suitable mounting location that is facing the RFID reader during normal driving. Reader Reader Tag Read Tag Read Zone Zone Avoid...
  • Página 4 One Year Limited Warranty within 24 hours of application. Please do not wash the area where the tag All RFID Tags sales are fi nal. However, LiftMaster warrants to the fi rst is installed or disturb the tag for 24 hours after installation.
  • Página 5 Pour obtenir un rendement maximal, l’étiquette RFID à double usage LiftMaster LMUNTG/SPLMUNTG (pare-brise/phare) doit être installée sur le pare-brise ou un autre point de montage adéquat faisant face au lecteur RFID pendant la conduite normale. Les étiquettes à accrocher (LMHNTG) doivent être attachées au rétroviseur pour produire des résultats optimaux.
  • Página 6 S’assurer que l’étiquette ne se trouve pas derrière une surface métallique quelconque ou le garnissage sombre autour de la glace. Pour l’étiquette LMHNTG, l’accrocher au rétroviseur.
  • Página 7 Installation de l’étiquette RFID à double usage LMUNTG sur le phare Pour obtenir un rendement maximal, l’étiquette RFID doit être installée sur le diffuseur du phare ou un autre emplacement de montage adéquat faisant face au lecteur RFID pendant la conduite normale. Zone de Lecteur Lecteur...
  • Página 8 économique Canada. Ces limites ont pour but de fournir une protection raisonnable contre le brouillage RFID d’une marque autre que LiftMaster. Si le système RFID ne se compose nuisible dans une installation résidentielle. Cet équipement génère, utilise et peut émettre des fréquences radio et, s’il n’est pas installé...
  • Página 9 Para un desempeño óptimo, la etiqueta de RFID de doble uso LiftMaster LMUNTG/SPLMUNTG (Parabrisas/Faro) debe instalarse en un parabrisas u otro punto de montaje adecuado que quede enfrente del lector de RFID durante la conducción normal. Las etiquetas colgantes (LMHNTG) se deben sujetar al espejo retrovisor para obtener mejores resultados.
  • Página 10 Montaje de la etiqueta de RFID - Parabrisas Los siguientes diagramas muestran las ubicaciones de montaje adecuadas de las etiquetas de RFID en el parabrisas. Elija una ubicación de montaje de la etiqueta que cumpla el código de vehículos local y esté por lo menos a 6.4 cm (2.5 pulg.)" de cualquier material que contenga metal. Esto incluye la línea del techo del vehículo, los pilares laterales y el bloque de montaje del espejo retrovisor.
  • Página 11 Instalación en el faro de la etiqueta de RFID de doble uso LMUNTG Para un desempeño óptimo, la etiqueta de RFID debe instalarse en la lente del faro u otra ubicación de montaje adecuada que quede enfrente del lector de RFID durante la conducción normal.
  • Página 12 Aun así, no hay garantía de que no se produzcan sistema de RFID que no es de marca LiftMaster. Si el sistema de RFID no es interferencias en una instalación particular. Si este equipo produce interferencia en la recepción de radio o un lector de RFID LiftMaster (LMSC1000) o una etiqueta de RFID LiftMaster televisión, lo cual puede determinarse apagando y encendiendo la unidad, el usuario debe tratar de corregir el...

Este manual también es adecuado para:

Lmuntg