Technical Data; Planer Safety Warnings - AEG PL 700 Manual Original

TECHNICAL DATA

Production code.....................................................................
Voltage...................................................................................
Frequency..............................................................................
Rated input ............................................................................
Power input............................................................................
Planing width .........................................................................
Planing depth max. ................................................................
Rabbet depth .........................................................................
Rated no-load speed .............................................................
Weight according EPTA-Procedure 01/2014 .........................
Noise/Vibration Information
Measured values determined according to EN 62841.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A))....................
Sound power level (Uncertainty K=3dB(A)) ........................
Wear ear protectors.
Total vibration values (vector sum in the three axes)
determined according to EN 62841.
Vibration emission value a
Uncertainty K ......................................................................
WARNING
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized
test given in EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of
exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for
diff erent applications, with diff erent accessories or poorly maintained, the vibration and noise emission may diff er. This may
signifi cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is
switched off or when it is running but not actually doing the job. This may signifi cantly reduce the exposure level over the
total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration and/or noise such as: maintain the
tool and the accessories, keep the hands warm, organization of work patterns.
WARNING Read all safety warnings, instructions,
illustrations and specifi cations provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.

PLANER SAFETY WARNINGS

Wait for the cutter to stop before setting the tool down.
An exposed rotating cutter may engage the surface leading
to possible loss of control and serious injury.
Hold the power tool by insulated gripping surfaces
only, because the cutter may contact its own cord.
Cutting a „live" wire may make exposed metal parts of the
power tool „live" and could give the operator an electric
shock.
Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
workpiece by your hand or against the body leaves it
unstable and may lead to loss of control
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Always wear goggles when using the machine. It is
recommended to wear gloves, sturdy non slipping shoes
and apron.
Wear ear protectors. Exposure to noise can cause hearing
loss.
18 ENGLISH
470 335 - PL700.indd 18 470 335 - PL700.indd 18
PLANER
.................................................
h
PL 700
..................... 4749 37 01...
...000001-999999
..................220-240 V
......................50/60 Hz
.........................700 W
.............................3 A
...........................82 mm
.............................3 mm
...........................12 mm
.....................17000 min -1
..........................2,8 kg
........................89,0 dB (A)
.........................100 dB (A)
..........................2,6 m/s
2
..........................1,5 m/s
2
Only plane with sharp blades and avoid metal (nails,
screws).
Never reach into the danger area of the machine when it is
running.
The dust produced when using this tool may be harmful to
health. Do not inhale the dust. Wear a suitable dust
protection mask.
Do not use compressed air to blow dust or debris. This
practice is dangerous and can cause dirt and grit to be
blasted off and injure someone's eyes.
Do not drill the housing, as the protective insulation would
be rendered ineff ective. Use adhesive labels.
Do not machine any materials that present a danger to
health (e.g. asbestos).
Switch the device off immediately if the insertion tool stalls!
Do not switch the device on again while the insertion tool is
stalled, as doing so could trigger a sudden recoil with a
high reactive force. Determine why the insertion tool stalled
and rectify this, paying heed to the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING! Danger of burns
• when changing tools
19.11.2019 12:29:53 19.11.2019 12:29:53