Intended Use; Safety Information - Woodstar SL8Lxu Manual De Instrucciones

• Check the device and accessory parts for transport
damage.
• If possible, store the packaging until the warranty
period has expired.
ATTENTION
The device and packaging materials are not toys!
Children must not be
allowed to play with plastic bags, film and small
parts! There is a risk of swallowing and
suffocation!
• Drag, crosscut and mitre Saw
• 1 x Clamping device (7)
• 2 x Workpiece support (8)
• Sawdust bag (17)
• Allen key (d)
• Allen key 3 mm (e)
• 2 x 1,5 V AAA Battery
• 2 x carbon brush
• Operating manual

4. Intended use

The drag, crosscut and mitre saw is designed to cross-
cut wood and plastic respective of the machine's size.
The saw is not designed for cutting firewood.
Warning! Not use the saw to cut materials other than
those specified described in manual.
Warning! The supplied saw blade is only intended for
the sawing of wood! Do not use this blade for the saw-
ing of plastic!
The equipment is to be used only for its prescribed
purpose. Any other use is deemed to be a case of mis-
use. The user / operator and not the manufacturer will
be liable for any damage or injuries of any kind caused
as a result of this.
The equipment is to be operated only with suitable
saw blades. It is prohibited to use any type of cutting-
off wheel.
To use the equipment properly you must also observe
the safety information, the assembly instructions and
the operating instructions to be found in this manual.
All persons who use and service the equipment have
to be acquainted with this manual and must be in-
formed about the equipment's potential hazards. It is
also imperative to observe the accident prevention
regulations in force in your area. The same applies for
the general rules of health and safety at work.
The manufacturer will not be liable for any changes
made to the equipment nor for any damage resulting
from such changes. Even when the equipment is used
as prescribed it is still impossible to eliminate certain
residual risk factors. The following hazards may arise
in connection with the machine's construction and
design:
22 GB
• Contact with the saw blade in the uncovered saw
zone.
• Reaching into the running saw blade (cut injuries).
• Kick-back of workpieces and parts of workpieces.
• Saw blade fracturing.
• Catapulting of faulty carbide tips from the saw blade.
• Damage to hearing if ear-muffs are not used as nec-
essary.
• Harmful emissions of wood dust when used in
closed rooms.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
equipment is used in commercial, trade or industrial
businesses or for equivalent purposes.

5. Safety information

Attention! The following basic safety measures must
be observed when using electric tools for protection
against electric shock, and the risk of injury and fire.
Read all these notices before using the electric tool
and keep the safety instructions for later reference.
Safe work
1 Keep the work area orderly
– Disorder in the work area can lead to accidents.
2 Take environmental influences into account
– Do not expose electric tools to rain.
– Do not use electric tools in a damp or wet envi-
ronment.
– Make sure that the work area is well-illuminated.
– Do not use electric tools where there is a risk of
fire or explosion.
3 Protect yourself from electric shock
– Avoid physical contact with earthed parts (e.g.
pipes, radiators, electric ranges, cooling units).
4 Keep children away
– Do not allow other persons to touch the equip-
ment or cable, keep them away from your work
area.
5 Securely store unused electric tools
– Unused electric tools should be stored in a dry,
elevated or closed location out of the reach of
children.
6 Do not overload your electric tool
– They work better and more safely in the specified
output range.
7 Use the correct electric tool
– Do not use low-output electric tools for heavy
work.
– Do not use the electric tool for purposes for which
it is not intended. For example, do not use hand-
held circular saws for the cutting of branches or
logs.
– Do not use the electric tool to cut firewood.