Ec Declaration Of Conformity - AEG BPS18-254BL Manual Original

TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods Legisla-
tion requirements.
Transportation of those batteries has to be done in accordance
with local, national and international provisions and regulations.
The user can transport the batteries by road without further
requirements.
Commercial transport of Lithium-Ion batteries by third parties is
subject to Dangerous Goods regulations. Transport preparation
and transport are exclusively to be carried out by appropriately
trained persons and the process has to be accompanied by
corresponding experts.
When transporting batteries:
Ensure that battery contact terminals are protected and insulated
to prevent short circuit. Ensure that battery pack is secured
against movement within packaging. Do not transport batteries
that are cracked or leak. Check with forwarding company for
further advice
BATTERY PACK PROTECTION
In extremely high torque, binding, stalling and short circuit situ-
ations that cause high current draw, the tool will stop for about 2
seconds and then the tool will turn OFF.
To reset, remove the battery pack from the tool and replace it.
Under extreme circumstances, the internal temperature of the
battery pack could raise too much. If this happens, the fuel gauge
will ash until the battery pack cooled down. After the lights go
o , the work may continue.
Place the battery on the charger to charge and reset it.
SPECIFIED CONDITIONS OF USE
The slide compound mitre saw is intended for sawing solid
and bonded wood with or without glued veneer, plastics, and
materials similar to wood.
The slide compound mitre saw is intended to be used only by adult
operators who have read the instruction manual and understand
the risks and hazards.
The slide compound mitre saw is designed to be xed at the base
to a solid bench top. If the base is not securely xed, the whole
machine may move during cutting operations, which increases
the possibility of serious personal injury.
The slide compound mitre saw is designed make bevel and
mitre cuts. The capacities for the various cuts are provided in the
product speci cations in this manual.
The slide compound mitre saw is to be used in dry conditions, with
excellent ambient lighting and adequate ventilation.
The slide compound mitre saw is intended for consumer use and
should only be used as described above and is not intended for any
other purpose.
MAINTENANCE
Do not modify this saw in any way or use accessories not approved
by the manufacturer. Your safety and that of others may be
compromised.
Do not use the saw if any switches, guards or other function of this
saw does not work as it is intended to. Return to an authorised
service centre for professional repair or adjustment.
Do not make any adjustments whilst the saw blade is in motion.
Removed the battery pack before making adjustments, lubrica-
ting or when doing any maintenance on the machine.
Before and after each use, check your saw for damage or broken
parts and keep it in top working condition by replacing parts
immediately with spares approved by the manufacturer.
The blade is very hot after use, wear gloves or allow to cool before
maintenance or cleaning procedures.
Clean out accumulated dust using a brush or vacuum cleaner. Do
not use compressed air.
To assure safety and reliability, all repairs, including changing
brushes, should be performed by an authorised service centre.
Be sure to disconnect the tool from the power supply before
attaching or removing the saw blade.
Clean tool and guarding system with dry cloth.
The ventilation slots of the machine must be kept clear at all
times.
Use only AEG accessories and spare parts. Should components
need to be replaced which have not been described, please
contact one of our AEG service agents (see our list of guarantee/
service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the Article No. as well as the machine type printed on the
label and order the drawing at your local service agents or directly
at: Techtronic Industries GmbH, Max-Eyth-Straße 10, 71364 Win-
nenden, Germany.

EC DECLARATION OF CONFORMITY

We declare under our sole responsibility that the product
described under "Technical Data" ful lls all the relevant provisions
of the directives
2011/65/EU (RoHS)
2006/42/EC
2014/30/EU
and the following harmonized standards have been used.
EN 62841-1:2015
EN 62841-3-9:2015+A11:2017
EN 55014-1:2006+A1:2009+A2:2011
EN 55014-2:2015
EN IEC 63000:2018
Winnenden, 2019-04-30
Alexander Krug / Managing Director
Authorized to compile the technical le
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
GB
English
33