Preparation For Use - FUNAI RFT909B El Manual Del Propietario

PREPARATION FOR USE

LANGUAGE SELECTION
If you want to change the language of the on-screen menu, follow the procedure below.
1
Connect the power cord.
Note: If some digits appear in the corner of the screen,
press the POWER button without unplugging the power cord.
2
Press the POWER button to turn on the TV.
3
Press the MENU button so that the menu display appears
on the TV screen.
4
Press the CH(annel) ▲ or ▼ button to point to "[ENGLISH]".
5
Select "ENGLISH" or "ESPAÑOL" = Spanish by using
the VOL(ume) ∆ or ∇ button.
6
Press the MENU button to exit the menu.
CHANNEL PRESETTING
To preset a channel or to change a preset channel, follow the procedure below.
1
Press the POWER button to turn on the TV.
2
Press the MENU button so that the menu display appears
on the TV screen.
3
Press the CH(annel) ▲ or ▼ button to point to "CHANNEL SET".
Then, press the VOL(ume) ∆ button.
OPERATIONS
WATCHING A TV PROGRAM
1) Press the POWER button to turn on the TV.
2) Select the desired channel with the CH(annel) ▲ or ▼ button.
3) Adjust the volume to the desired listening level using the VOL(ume) ∆ or ∇ button.
4) Adjust picture controls for a natural looking image. (See "PICTURE ADJUSTMENT".)
SETTING THE SLEEP TIMER
The sleep timer function enables you to shut off the power without pressing
the POWER button after a desired time period.
1) Press the POWER button to turn on the TV and press the SLEEP button
on the remote control .
2) You may change the sleep time with pressing the SLEEP button on the
remote control repeatedly. The timer is set up to 90 minutes, 10 minutes
each time the SLEEP button is pushed. (The timer display counts up and sleep timer will be
displayed on the screen when you press the SLEEP button on remote control.)
Note: If you have a power failure, the sleep time will be lost.
PICTURE
CHANNEL SET
[ENGLISH]ESPAÑOL
PICTURE
CHANNEL SET
[ENGLISH]ESPAÑOL
PICTURE
CHANNEL SET
[ENGLISH]ESPAÑOL
PICTURE
CHANNEL SET
[ENGLISH]ESPAÑOL
SLEEP 10
To cancel the sleep timer:
Press the SLEEP button repeated-
ly until "SLEEP 0" is displayed.
4
Press the CH(annel) ▲ or ▼ button to point to "AUTO MEMO".
Then, press the VOL(ume) ∆ button.
The tuner scans and memorizes all active channels in
your area.
●
The TV distinguishes between standard TV channels
and cable channels.
●
When AUTO MEMO action is completed, the lowest
memorized channel reappears on the screen.
When you press the CH(annel) ▲ or ▼ button after
●
selecting AUTO MEMO, the tuner will stop at the memorized
channels only.
●
When AUTO MEMO action is stopped in the middle of activity,
the tuner is into CATV mode. To receive standard TV channels,
you must follow AUTO MEMO action again.
●
The TV may recognize TV channels to be CATV channels
by the receiving conditions. In this case, try AUTO MEMO action again
in the fine receiving conditions.
[ADD/DELETE FUNCTION]
1) Press the MENU button so that the menu display appears on the TV screen.
2) Press the CH(annel) ▲ or ▼ button to point to "CHANNEL SET".
Then, press the VOL(ume) ∆ button.
3) Press the VOL(ume) ∆ button so that "ADD/DELETE" is selected.
4) Use the CH(annel) ▲ or ▼ button to select the
channel you wish to put into memory or to erase from memory.
Note: The display will return to the screen in about 10 seconds.
Perform "ADD/DELETE" function while this display appears
on the screen.
●
Press the VOL(ume) ∆ or ∇ button to light up the channel number
in LIGHT BLUE if you wish to add the channel into memory.
●
Press the VOL(ume) ∆ or ∇ button to light up the channel number
in LIGHT RED if you wish to erase the channel from memory.
5) Press the MENU button to exit the menu.
[SEARCH FUNCTION]
If TV can not receive the preset channel, you can seek the 1st available channel by keeping to
press the CH(annel) ▲ or ▼ button.
When you seek the next available channel, keep to press the CH(annel) ▲ or ▼ button again.
PICTURE ADJUSTMENT
1) Press the MENU button so that the menu display appears on the TV screen.
2) Press the VOL(ume) ∆ button so that "PICTURE" is selected.
3) Select the feature you wish to adjust with the CH(annel) ▲ or ▼ button and adjust it with the
VOL(ume) ∆ or ∇ button.
GAME MODE
Set to the most suitable position for TV
GAME.
[+] : ON
[-] : OFF
BRIGHT
Adjust until the whitest parts of the picture are
as bright as you prefer.
[+] : increase brightness
[-] : decrease brightness
CONTRAST
Adjust to increase or decrease contrast.
[+] : increase contrast
[-] : decrease contrast
COLOR
Adjust to be brilliant or pale color.
[+] : be brilliant color
[-] : be pale color
TINT
Adjust to obtain natural skin tones.
[+] : greenish tone
[-] : reddish tone
Notes:
●
"+" is achieved by pressing the VOL(ume) ∆
button and "-" by pressing the VOL(ume) ∇
button.
: Press the CH(annel) ▲ or ▼ button.
[-] [+] [-] [+]
GAME MODE BRIGHT
OFF ON
PICTURE
CHANNEL SET
[ENGLISH]ESPAÑOL
●
In the above steps, the picture adjustment
display will disappear from the TV screen
after about 10 seconds unless you press any
buttons, even though you may not be fin-
ished. Press the MENU and VOL(ume) ∆
button so that "PICTURE" is selected. Then,
press the CH(annel) ▲ or ▼ button repeat-
edly until the display returns to the screen.
●
If you adjust the other Picture control after
you set the Game mode to [ON], the Game
mode is set to [OFF] automatically. If you
want to set the Game mode, reset it to [ON].
[USING THE INPUT SELECT BUTTON]
You may also set the Game mode and external
input mode at the same time by pressing the
INPUT SELECT button repeatedly on the remote
control. "GAME" appears on the TV screen.
●
To exit the Game mode and external input
mode, press the INPUT SELECT button
repeatedly on the remote control.
●
To cancel the Game mode only, adjust the
picture control. In this case, "VIDEO1"
instead of "GAME" appears on the TV screen.
●
When you set the Game mode if the TV is
off, the TV turns on and will be in the Game
mode and external input mode automatically.
[-] [+] [-] [+]
CONTRAST COLOR
ADD/DELETE
AUTO MEMO
ADD/DELETE
AUTO MEMO
[-] [+]
TINT