Electrical Safety - Black+Decker KW1200E Manual Del Usuario

The vibration level may increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
The following pictograms, along with the date code, are shown
on the tool:
Warning! To reduce the risk of injury, the user
must read the instruction manual.

Electrical safety

This tool is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard
Features
This tool contains all or some of the following features:
1. On/off switch
2. Lock-off button
3. Variable speed control knob
4. Plunge lock lever
5. Spindle lock button
6. Collet
7. Revolver depth stop
8. Chip deflector
9. Depth stop bar
10. Depth of cut scale
11. Dust extraction adaptor
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting a router bit (fig. A)
Remove the chip deflector (8).
u
Keep the spindle lock button (5) depressed and rotate the
u
spindle until the spindle lock fully engages.
Loosen the collet nut (12) using the spanner provided.
u
Insert the shank of the router bit (13) into the collet (6).
u
Make sure that the shank protrudes at least 3 mm from
the collet as shown.
(Original instructions)
Keep the spindle lock button (5) depressed and tighten the
u
collet nut (12) using the spanner provided.
Fitting the edge guide (fig. B)
The edge guide helps to guide the tool parallel to an edge.
Fit the bars (14) to the edge guide (15) using the two
u
screws (16) provided.
Insert the bars (14) into the router base as shown.
u
Set the edge guide to the required distance.
u
Tighten the fixing screws (17).
u
Fitting the dust extraction adaptor (fig. C)
The dust extraction adaptor allows you to connect a vacuum
cleaner to the tool.
Connect the hose (18) of the vacuum cleaner to the
u
adaptor (11).
Fitting the template guide (fig. D)
Fit the template guide (19) to the base of the router, with
u
the flange to the bottom (workpiece) side.
Insert the two long screws (20) from the bottom side
u
through the template guide and the holes in the base.
Place a nut onto each of the screws and securely tighten
u
the nuts.
Fitting the distance piece (Optional) (fig. E)
Fit the distance piece (21) to the base of the router using
u
the screws provided.
Fitting the centring pin (fig. F)
Fit the centring pin (22) to the workpiece side of the bars,
u
then tighten it with the steel knob (23) provided .
Fitting the copy follower (Optional) (fig. G)
Fit the edge guide to the router as shown in fig. B.
u
Fit the 'L' bar(24) to the upper side of the edge guide
u
using the two screws and nuts provided.
Adjust the rotating attachment (25) on the 'L' bar with the
u
wing knob (26).
Use
Warning! Let the tool work at its own pace. Do not overload.
Carefully guide the cable in order to avoid accidentally
u
cutting it.
Adjusting the depth of cut (fig. H, I & J)
The depth of cut is the distance X between the depth stop bar
(9) and the depth stop (7). The depth of cut can be set in two
different ways as described below.
Adjusting the depth of cut using the scale (fig. I)
Fit the router bit as described above.
u
ENGLISH
9