Protection Devices - Adler AD 1295 Manual De Uso

lid. Do not open the lid during boiling in kettle or immediately after boiling, because steam
coming out of lid can cause burns.
21. Move the kettle only by holding it by handle..
22. Never fill kettle above MAX level and below MIN level. It may cause damage of kettle.
23. Never switch on kettle without water.
24. Never use kettle without filter or with open cover (automatic shutdown will not work).
25. Descale your kettle regularly. Using kettle with heating element covered by scale may
cause damage.
26. Do not use aggressive detergents to wash the kettle housing - they can damage the
kettle or remove the markings.
27. The device is not designed to work with external schedulers or separate remote
control system.
28. Do not wash the base of the kettle directly in the water, just wipe with a dry cloth.
29. Children aged 3 to 8 years old can enable and disable the device only when it is in its
normal position of use, they are supervised or instructed on the safe use and understand
the resulting risks. Children aged 3 to 8 years old can not connect device, operate, clean
or maintain.
DESCRIPTION OF THE DEVICE. ELECTRIC KETTLE AD1295
1. Lid
4. Handle
7. Power knob / temperature control
BEFORE FRIST USE
Fill the kettle three times with water to the maximum level, boil and pour it. To remove any factory odor.
BASIC OPERATION:
SINGLE WATER BOLING UP TO 100 ℃
1. Fill the kettle with water so that the water level is between the maximum and minimum levels on the water level indicator under the
handle (4).
2. Place the base (5) on a stable, flat and heat-resistant surface.
3. Remember to close the kettle with the lid (1) after filling, otherwise the kettle will not switch off automatically when the water boils.
4. Insert the power plug into the 220-240V ~ 50 / 60Hz power socket. Place the kettle on the base (5), the knob (7) will light red, wait
until you hear the "di-di" sound twice.
5. Press the knob (7), the knob will turn green, the display (2) will blink twice, indicating 100 ℃, then the heater will start heating the
water, and the LCD display (2) will show the current water temperature . The water temperature will rise until it boils, i.e. up to 100 ° C.
6. After the water boils, the kettle will automatically turn off, the knob (5) will turn red, you will hear the "di-di" sound twice.
7. To turn off the kettle before the water finish boiling, lift it off the base (5).
8. You can start the kettle again after approximately 2 minutes from the last use.
9. When the device is not in use, the display (2) and knob (7) turn off lighting after 5 minutes.
ADVANCED OPERATION:
SINGLE WATER BOILING TO THE SELECTED TEMPERATURE 40 ℃ OR 50 ℃ / 60 ℃ / 70 ℃ / 80 ℃ / 90 ℃
Put the kettle on the base (5), wait until you hear the "di-di" sound twice. Briefly press the knob (7), the knob will turn green, you will
hear a single "di" sound, turn the knob clockwise (or vice versa), the display (2) will show the temperature you choose 40 ℃ (or 50 ℃ /
60 ℃ / 70 ℃ / 80 ℃ / 90 ℃) and blinks three times remembering the setting of the selected temperature level. Then the display will
show the current water temperature inside the kettle. The kettle will stop boiling water when it reaches the selected temperature level of
40 ℃ (or 50 ℃ / 60 ℃ / 70 ℃ / 80 ℃ / 90 ℃), the knob (7) will turn red, you will hear the "di- di "sound twice.
KEEP WARM FUNCTION AT THE SELECTED TEMPERATURE 40 ℃ OR 50 ℃ / 60 ℃ / 70 ℃ / 80 ℃ / 90 ℃ / 100 ℃
Put the kettle on the base (5), wait until you hear the "di-di" sound twice. Press the knob (7) FOR 2 SECONDS until the icon (8)
appears on the display (2), the knob turns green and flashes, turn the knob clockwise (or counterclockwise), the display (2) will show
the temperature you choose 40 ℃ (or 50 ℃ / 60 ℃ / 70 ℃ / 80 ℃ / 90 ℃) and blink three times remembering the setting of the
selected temperature level. Then the display will show the current water temperature inside the kettle. The kettle will stop boiling water
when it reaches the selected temperature level of 40 ℃ (or 50 ℃ / 60 ℃ / 70 ℃ / 80 ℃ / 90 ℃), you will hear a single "di" sound, the
knob will turn red and will blink for 2 hours. Within 2 hours, the kettle will heat the water cyclically, constantly displaying the selected
temperature level to maintain. When the water temperature drops by 5 ℃ in relation to the selected temperature level of 40 ℃ (or 50
℃ / 60 ℃ / 70 ℃ / 80 ℃ / 90 ℃), the device will turn on automatically and heat it.
Note: Only during this procedure, the keep warm function will be active. After removing the kettle from the base, the keep warm
function function settings will be reset.

PROTECTION DEVICES

The device is equipped with an automatic fuse against overheating, the fuse will trip when the kettle was used with insufficient water.
Always make sure that the volume of water in the appliance is above the minimum level. If the fuse turns on, turn off the kettle by
pressing the knob (7), then remove the plug from the power socket and allow the kettle to cool for 5-10 minutes. Then fill the kettle with
water and turn on the device that will operate normally.
2. LCD display
5. Base
3. Housing
6. Mesh filter
8. Keep warm function indicator
4