Modellsport MULTIPLEX EasyGlider pro Instrucciones página 4

!
These operating instructions are an integral part of the
product. They contain important information and safety
notes, and should be kept in a safe place at all times. Be
sure to pass them on to the new owner if you ever dispose
of the product.
1. I
NTRODUCTION
Our "Easy Glider electric TUNING" power set, # 33 2629,
provides a significant improvement in the climb perform-
ance of the Easy Glider electric, thanks to its excellent ef-
ficiency and increased power output compared with the
standard power set. The result is that the model is cap-
able of several steep climbs from a single charge, taking
it to a good height for extended thermal flights.
2. C / R
ONTENTS EPLACEMENT PARTS
• 1 Himax A 2815-3100 with pre-fitted metal 3 : 1 gearbox
• 1 MULTIcont BL-27/II speed controller
• 1 carbon folding propeller
• 1 aluminium driver and spinner
• Various small items for installation in the model
Spare parts:
• Motor Himax A 2815-3100
• 3 : 1 metal gearbox with motor pinion
• Motor pinion for 2.3 mm ∅ shaft, 10-tooth / m = 0.5 # 33 2683
3. T . O
YP PERATIONAL
S "E G
ET ASY LIDER ELECTRIC
2S LiPo / 11" x 8" prop
Recommended Battery:
MULTIPLEX Li-BATT BX 2/2100
If you use the Himax A 2815-3100 motor and the stan-
dard propeller supplied in the set, do not use more than a
2S LiPo pack or 6 NiXX cells
4. S N
AFETY OTES
The power set "Easy Glider electric TUNING" is designed
exclusively for use in modelling applications. Incorrect
use can result in serious personal injury.
• Read the instructions before initiation
• Before every flight, check that the motor and propeller
are securely mounted
• Remove all movable objects from the area around the
propeller before switching the motor on
• Do not allow clothing or any of your extremities to get
close to the spinning propeller
• Never start running the motor in your hand
• Stop the motor immediately if you notice vibration.
Eliminate the cause of the vibration before running it
again; you may need to correct the balance of the pro-
peller
•
Make sure the power system is adequately cooled; do
not allow anything to obstruct the free circulation of air
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de
Operating Instructions for the
"Easy Glider electric TUNING" Power Set
# 7 2275
# 73 3187
# 73 3186
# 33 3041
# 33 2684
D P
ATA OF OWER
TUNING"
Current drain: approx.18.0 A
# 15 7130
.
5. A
SSEMBLING THE
"E G
ASY LIDER ELECTRIC
1. First place the motor in the model, and secure it with
the motor retainer as described and illustrated in the
building instructions supplied with the Easy Glider
electric. The Himax A 2815-3100 with pre-fitted metal
gearbox replaces the standard geared brushed motor.
2. Attach the folding propeller blades to the driver using
the screws and self-locking nuts supplied. Ensure that
the propeller blades rotate smoothly forward and back.
3. Fit the driver / folding propeller blades assembly on the
gearbox shaft, and fit the grubscrews to secure it;
tighten the grubscrews firmly.
4. Fit the spinner on the driver and secure it with the
retaining screw.
6. U P
SING THE OWER
TUNING"
ELECTRIC
1. Connect the three wires attached to the speed control-
ler to the three wires attached to the motor; the order of
connection is unimportant.
2. Locate the UNI connector attached to the speed con-
troller, and connect it to your receiver.
3. Switch the transmitter on, and check that the throttle
control is at the "OFF" position.
4. Connect the flight battery to the speed controller.
5. Check the direction of rotation of the motor: it should
spin clockwise when viewed from the tail, looking for-
ward. If this is not the case, disconnect the flight battery
and swap over any two of the three motor wires.
6. Switch on the motor brake at the speed controller; the
method of doing this is described in the instructions
supplied with the controller.
P S
OWER ET
TUNING"
S "E G
ET ASY LIDER
FOR THE FIRST TIME
Page 1/2