FLETCHER 3100 Manual Del Propietário página 6

Ocultar thumbs Ver también para 3100:
Tabla de contenido

Publicidad

INSTALLATION
It is important to mount the machine on the wall securely, safely, and rigidly. At least two people will be required to lift the machine for
wall mounting.
The following major steps are required for installation:
1.
Attach the UPPER BRACKET to the wall.
2.
Attach the LOWER BRACKET to the machine.
3.
Lift and bolt the machine to the UPPER BRACKET.
4.
Attach the LOWER BRACKET to the wall.
5.
Install the left HORIZONTAL SUPPORT to the wall and machine.
6.
Install the RIGHT SUPPORT.
Detailed procedures are as follows: Refer to the facing page to identify fasteners.
1.
Hold the UPPER BRACKET, Figure 6, against the wall with the top about 93"
(2360mm) above the floor. Use a level to be sure it is vertical. Mark the wall through
the 6 mounting holes. Drill pilot holes in the wall and install the UPPER BRACKET
with six hex head wood screws from the parts bag, shown at A on the facing page.
NOTE: The UPPER BRACKET must be safely mounted to wood, not plaster. If
wooden studs are not present, you can rigidly mount a sheet of plywood to the wall
and attach the UPPER AND LOWER BRACKETS to the wood.
2.
Use two 1/4-20 bolts, nuts, washers, and lock washers shown at H to attach the
LOWER BRACKET to the machine. See Figure 7.
3.
Lift the machine and attach it to the UPPER BRACKET with four 1/4-20 bolts,
washers, lock washers, and nuts shown at H. See Figure 6.
The holes in the UPPER BRACKET are elongated to allow the LOWER BRACKET to
rest squarely against the wall.
4.
Use the LOWER BRACKET as a guide to drill pilot holes in the wall and secure
with three hex head wood screws, A.
5.
Install the HORIZONTAL SUPPORT
and the wall. See Figure 7. Use two 10-24 pan head bolts and nuts, shown at C
and two hex head wood screws, A.
6.
Refer to Figure 7 to install the RIGHT SUPPORT assembly.
A.
Attach the brace to the RIGHT SUPPORT with two flat head screws and
nuts, D. Leave the nuts slightly loose.
.
B.
Remove the two hex nuts, lock washers and washers from the vertical leg
of the ANGLE BRACKET in the back of the machine.
Set them aside to reinstall later.
C.
Loosen, (do not remove), the button head hex screw in the RIGHT SUPPORT.
D.
Attach the second ANGLE BRACKET to the top left end of the RIGHT SUP-
PORT with two 1/4-20 bolts, washers, lock washers, and nuts ( B). The long
leg
of the angle bracket must be horizontal. Do not tighten yet.
E.
Hold the RIGHT SUPPORT in position with the left end of the
SQUARING EDGE BAR in the machined slot of the machine. Place
the shoulder screw, F, through the SQUARING EDGE BAR
and attach a washer, lock washer and nut in the rear.
F.
Install the two hex cap screws, G, at the top of the brace and right
edge of the machine.
G.
Reinstall the washers and nuts you removed in step 6. B. You will note
both ANGLE BRACKETS are attached to the machine with the same bolts.
H.
Now, in sequence, fully tighten the ANGLE BRACKET nuts, the shoulder bolt
nut,
and the screws and nuts at both ends of the BRACE.
I.
Install the remaining HORIZONTAL SUPPORT
RIGHT SUPPORT and the wall using fasteners C and A.
(Continue Page 10)
between the LEFT SUPPORT
between the
6
1/4-20 BOLT HOLES
MACHINE
BOLZENLÖCHER
MASCHINE
WOOD SCREW HOLES
HOLZSCHRAUBENLÖCHER
UPPER BRACKET
OBERE HALTERUNG
Figure 6
CLAMP
KLEMMVORRICHTUNG
HORIZONTAL
SUPPORT
ANGLE
BRACKET
WINKELSTÜCK
MACHINED
SLOT
EINSCHNITT
LEFT
SUPPORT
LINKE HALTERUNG
SQUARING
EDGE BAR
WINKELLEISTE
LOWER
BRACKET
BUTTON HEAD
UNTERE HALTERUNG
SCREW
HALBRUNDKOPFSCHRAUBE
Figure 7
UPPER BRACKET
OBERE
HALTERUNG
BRACE
STÜTZE
HORIZONTAL
SUPPORT
HORIZONTALE
HALTERUNG
RIGHT
SUPPORT
RECHTE
HALTERUNG

Publicidad

Tabla de contenido
loading

Productos relacionados para FLETCHER 3100

Tabla de contenido