Led Floodlight; Technical Data - Ritos A1D08A1 Indicación Para El Montaje Y El Servicio

GB

LED floodlight

Operation and maintenance manual
Dear valued customer,
Thank you for purchasing our floodlight. Before operating the floodlight, please read the following
instructions for use carefully and keep them in a safe place for future reference.
Proper Use
The floodlight is spray-protected, IP65 and for use outdoors.
The floodlight conforms with the appropriate European CE regulations
General Safety Instructions
• Never look directly into the led light source. The light emitted can contain the colour blue.
• Use only with a sufficiently protected 230v~ installation.
• Must not be immersed in water or other liquids.
• Must not be operated with wet hands; never look directly into the light source.
• Must never be covered.
• Must never be operated with an open housing, missing or damaged wiring compartment, or
missing or damaged lens.
• Must never be sprayed or cleaned using a steam pressure cleaner since this can damage the
insulation and seals.
• Must never be repaired by the user. Repairs must only be carried out by the manufacturer or an
authorized service representative.

Technical Data

• Type A1D08A1: Illuminant: 7W LED
• Type A1D14A1: Illuminant: 12W LED
• Voltage: 230V~, 50Hz
• Protection class: IP65
• Colour temperature: 6500K
Installing
Installation may only be carried out by trained professionals according to the applicable installation
regulations. Contact a licensed electrician. ATTENTION!! Before installation, the power supply must
be disconnected and locked out.
• Loosen the screws on the side of the housing and remove the mounting brackets.
• Install the mounting brackets to a suitable surface – always follow the installation location requi-
rements listed under "General Safety Information".
• Reattach the floodlight housing to the mounting brackets but do not tighten the screws fully.
• Loosen the screws on the back of the junction box and remove the cover.
• Remove the cable guide screw connection and guide it over the connecting cable – the screw
connection thread must face in the direction of the cable end.
• Loosen the cable grip screws and remove the cable grip.
6
Luminous flux: approx. 600lm
Luminous flux: approx. 1000lm
• Guide the screw connection seal over the cable as well, and then insert the cable into the junction
box. Ensure the seal is seated in the cable guide correctly – if the connecting cable is too thin,
the cable guide must be additionally sealed.
• Connect the wires according to Figure 1.
• Tighten the cable guide screw connection, install the cable grip, and tighten the screws.
• Install the junction box cover and tighten the screws.
Setting the Floodlight Direction
Loosen the screws on the sides of the mounting brackets, adjust the floodlight direction, and then
retighten all screws.
Cleaning
• Disconnect and lock out the power supply to the floodlight. Allow the floodlight to cool down
sufficiently!
• Clean with a dry or slightly moist, clean, lint-free cloth and a mild detergent if required. Do not
use cleaners that contain abrasives or solvents.
Maintenance
• If the lens is damaged it must be replaced immediately.
• Clean any dirt from the housing or the lens immediately, since it could cause overheating.
WEEE-reference of disposal
In accordance with European defaults used electrical and electronics devices may no
more be given to the unsorted waste. The symbol of the waste bin on wheels refers to the
necessity of separate collection.
Please help with environmental protection and see to it that this device is given to the for
this purpose designated systems of waste sorting if you do not use it any longer.
DIRECTIVE 2012/19/EU of the EUROPEAN PARLIAMENT AND OF the COUNCIL of 4 July 2012 on
waste electrical and electronic equipment (WEEE).
Warranty
During manufacturing this Ritter Leuchten product is passed through several quality testing
stations which are set up with newest technology. Should nevertheless a defect arise, Ritter
Leuchten offers a warranty to the following extent:
1. The duration of the warranty is 24 months after the date of purchase.
2. The unit is either repaired or replaced by Ritter Leuchten free of charge or if it can be
shown that it has become unusable during the warranty period due to a manufacturing
or material defect.
3. The liability does not cover transport damages or damaged incurred through defective
installation.
4. If Ritter-Leuchten repudiates the warranty claim and no objection is made within 6
months, the right to repair becomes time-barred.
5. In a warranty case the unit must be sent to the dealer or Ritter Leuchten together with
the sales slip and a short description of the defect.
6. If there is no proof for a warranty liability being in place, any repair carried out will be invoiced.
GB
7