Introduction; Items Required For Operation; Glossary; Safety Precautions - Merlin Tracer 180 Manual Del Usuario

Introduction

Specification
Main Rotor Diameter
Fuselage Length
Flying Weight
Battery
Transmitter
Receiver
Servos
Charger

Items required for operation

4 * AA Batteries for the Transmitter

Glossary

Landing gear - Legs on the underside of helicopter.
Rotor - High speed rotating blades used to lift the helicopter into the air.
Throttle - A control function to adjust the speed of the rotating blades & height of the helicopter.
Rudder - A control function to turn the helicopter.
Cyclic Controls - Control functions to move the helicopter in flight.
Fuselage - Main body of the helicopter containing motor, receiver, speed control, servos and battery
Gyro - An electronic stabiliser built into the helicopter to assist flight.
LED - A coloured indicator light.
Swash Plate - Rotating plate below the rotor that adjusts the blade angles.

Safety Precautions

•
Read and follow this manual completely, observing all instructions and safety directions. Otherwise, serious injury and damage can occur.
Think about your safety, and the safety of others, first.
• Hold the product securely when the flight battery is plugged in, keep the rotor away from body parts and clothing, even it isn't spinning, as
it could be turned on by accident. Beware of hair becoming entangled in the rotor.
•
Do not fly when it's too windy or you may lose control and crash, causing injury or damage. Never fly near people, vehicles, train tracks,
buildings, power lines, water, hard surfaces or trees. Never allow anyone to attempt to catch the model while it's in flight or serious injury
may result.
• Adult supervision for flying and battery charging is recommended for pilots age 14 and younger.
• Only use a battery charger that is compatible with the flight battery. Never leave the charger unattended while charging. This will help
prevent overcharging and make sure damage does not occur to the battery, charger or any other property. While charging, place the
battery on a heat-resistant surface. Do not lay it on carpet or upholstery while charging.
•
Never cut into the battery, charger, or aeroplane wires or serious injury may occur. Causing the battery to "short out" (crossing negative
and positive bare wires) can cause fire, serious injury and damage.
• When you finish flying your product, always unplug the battery before you turn off the transmitter.
•
Always check that the transmitter has full control of the helicopter before flying.

Charging the battery pack

Use the supplied charger to charge the supplied battery. Other products are available and if used, you must follow the products instructions to
avoid damage.
The typical charge time for a flat battery is 110 minutes.
1. Connect the 240V wall mounted transformer (12V output) to the input side of the supplied charger, the red power indicator should glow.
2. Plug the battery into the 7.4V 2-cell output socket of the charger. The charge indicator should glow red to indicate charging is taking place.
3. When charging is complete the charger will automatically stop charging and the charge indicator will glow green.
4. Unplug the battery and input to the charger.
Cautions
•
Use the charger with adult supervision. Do not use the charger near water or when wet.
•
Do not use the charger if the wire is frayed or worn. If the wire is frayed or worn a short circuit can cause a fire or burns.
• If your battery gets hot and exceeds 50 degrees C during charge it may be faulty and you should contact your retailer
•
If the battery pack bulges or expands during charge or use it is faulty and you should contact your retailer.
• Never leave your battery pack on charge unattended.
Tracer 180
340mm
355mm
231.5g
Motor 180 Size Brushed
7.4V 800 mAh Li-Po Battery
MTX-47 2.4 GHz 4 Channel
MRX-47-2 2.4 GHz 4 in 1 Board
2 x Micro Servos
Mains 240V Li-Po Balance Charger Mains 240V Li-Po Balance Charger
Tracer 240
380mm
355mm
180 Size Brushed
7.4V 800 mAh Li-Po Battery
MTX-47 2.4 GHz 4 Channel
MRX-47-1 2.4 GHz 4 in 1 Board
2 x Micro Servos
2
185g