Sensitech TempTale Ultra Guia De Inicio Rapido página 3

The TempTale
Starting a TempTale Ultra Humidity Monitor
®
• Press and hold the Start button (1 – 3 seconds) until the Sunshine icon
The LED (2) will blink GREEN
• The monitor will begin to record temperature and humidity data after the programmed start-up delay period has passed.
Marking an Event and Reading Data on the LCD Screen
• To mark an event while the monitor is recording, press and release the Start button. An Arrow
at the top of the LCD screen and trip summary data will display. Press and release the Start button to cycle through the
trip summary data. Data appears in the following order:
1. Average temperature recorded (AVG)
2. Minimum temperature recorded (MIN)
3. Maximum temperature recorded (MAX)
4. Average RH% value recorded
5. Minimum RH% value recorded
6. Maximum RH% value recorded
7. Current temperature reading (If this LCD option is enabled)
8. Current RH% reading (If this LCD option is enabled)
Alarming
When the TempTale Ultra Humidity monitor is exposed to relative humidity and/or temperatures
outside the programmed alarm limits, an
will display if the high alarm(s) were triggered. The
triggered.
Stopping and Receiving a TempTale Ultra Humidity Monitor
There are two ways to stop a TempTale Ultra Humidity monitor:
• Press and hold the Stop button (1 – 3 seconds) until the Stop icon
upper right corner of the screen.
• Plug the monitor into a USB port on a computer.
NOTE: If the monitor is not stopped manually, the TempTale Ultra Humidity monitor will
continue to record data until it is plugged into a USB port on the computer or until the pro-
grammed trip length is reached.
Accessing TempTale Ultra Humidity Monitor Data Files
• After the monitor is stopped, plug the monitor into a USB port on the computer. The LED
RED
will blink while the Adobe
RED LED stops blinking and displays solid GREEN, the file generation process is complete.
The files are now accessible. (Windows
NOTE: Do not disconnect the monitor from the USB port while the
Managing and Viewing TempTale Ultra Humidity Monitor Files
• If the computer has Adobe PDF compatible reader software installed, double-click the PDF
file icon to open and view the PDF file.
• If the computer has Sensitech's TempTale Manager
higher), double-click the TTV file icon to open and view trip summary statistics and the
time-temperature graph.
• Both the PDF and TTV files can be copied, saved, or emailed as an attachment.
Direct USB Printing of PDF Reports
• To place the monitor in Direct Print mode, press and hold the Start and Stop buttons
RED
simultaneously until the
NOTE: Direct Print mode times out after approximately 10 seconds. If time out occurs
before the monitor is connected to a USB port, repeat the previous step.
• While the LED is blinking, plug the monitor into the USB port located on the exterior of a
USB-enabled printer, and then print the PDF report.
NOTE: Not all USB printers support USB-direct printing of PDF documents. Consult your
printer's user manual for support.
Ultra Humidity monitor can be programmed with custom start-up delays,
®
measurement intervals, and temperature/humidity alarm settings.
to indicate that the monitor has been started.
will appear at the top of the screen. The
icon will display if the low alarm(s) were
PDF report and TTV data file are being created. When the
®
7, 8.1, and 10).
®
Desktop Software installed (8.3 or
®
LED starts blinking. The monitor is now in Direct Print mode.
appears on the LCD screen (1).
icon will appear briefly
icon
2
appears in the
1
RED LED is blinking.
1. Temperature display indicator
2
3. Start-up delay
4. Marked point
5. Alarm Status
6. Current temperature (pre-programmed to display °C or °F)
7. Alarm triggered
8. Stopped recording
9. Avg/min/max relative humidity (RH%) recorded
10. Current relative humidity
3
1
Displayed Information
Sample running display, no alarm
3 4 5
Sample stopped display, with alarm
7
Running
= alarm(s), = no alarm(s)
HIGH / LOW
2
6
8
9
10