Delton RA Guia De Inicio Rapido página 6

4.4 Cancelling one transmitter from the memory module of the control unit.
a a a a b b b b
Press the hidden
button "e"
LED LED LED LED
c c c c d d d d
e e e e
Press the hidden
button "e" + "a"
a a a a b b b b
c c c c d d d d
e e e e
Attention: Do not use this procedure in presence of two or more control units close to each other. Because each control unit
nearby could be affected. We recommend to cut the power supply to the non interested control units.
4.5 Total reset of the memory of a control unit
1) Interrupt power to the unit
2) Keeping pressed the "learning key "x" supply the unit again. A series of beeps or flashings will indicate that the transmitters are now cancelled.
After such operation the control unit will give a series of fast beeps or blinkings followed by slower ones to signal that the mem-
ory is empty after which the unit will enter in the learning mode awaiting the signal of a transmitter.
LED LED LED LED
Blinker
ON
5. Advanced configuration: Possible configuration of the jumpers
Transmitters:
A slight pressure on the open/close keys triggers a short opening/closing movement (click). This permits Venetian blind type
adjustment. Prolonged pressure fully opens/closes the shutter. Pressure on the opposite direction of movement key causes stop,
subsequent pressure causes reversal of direction of movement.
Wall buttons connected by cable:
Operation is the same as that of the remote-control keys for inch movement, useful for Venetian blinds.
J1 J2
Prolonged pressure on the open key causes opening. Subsequent pressure on the same key stops opening. Pressing the close key
causes reversal of direction of movement (closing). Operation is mirrored for the other key.
Transmitter reception:
Disabled.
Wall buttons connected by cable:
these feature "deadman" operation, meaning the shutter elevates/drops as long as the buttons are pressed. Once these are released
J1 J2
the shutter stops.
Transmitters:
By pressing the key, the shutter opens completely; when the same key is pressed again, the shade is not blocked. By pressing the
opposite key once, movement stops, by pressing again the shutter closes.The same goes for the other key.
Wall buttons connected by cable:
J1 J2
Operation is the same as the remote-control buttons.
Transmitters:
Operation is by an inch key; when the key is pressed once, the shutter opens; when pressed again, the shutter stops, when pressed
a third time, the shutter closes. In this mode, one key only is stored for each transmitter.
Wall buttons connected by cable:
operation is by 2 inch keys; when the key is pressed once, opening starts; when pressed again, opening stops, when pressed a third
time, opening starts again. The same goes for closing, with relevant key.
NOTES: In this mode the unit is controlled by a single transmitter key, the first one that has been stored. If "a" key is first stored and
J1 J2
the jumpers are set according to the configuration beside ,the 'b' key will not have any effect if pressed . Vice versa if the 'b' key has
been stored first , this will control the unit , and key 'a' remains disabled.
GUARANTEE - In compliance with legislation, the manufacturer's guarantee is valid from the date stamped on the product and is restricted to the repair
or free replacement of the parts accepted by the manufacturer as being defective due to poor quality materials or manufacturing defects. The guarantee
does not cover damage or defects caused by external agents, faulty maintenance, overloading, natural wear and tear, choice of incorrect product, as-
sembly errors, or any other cause not imputable to the manufacturer. Products that have been misused will not be guaranteed or repaired.
Printed specifications are only indicative. The manufacturer does not accept any responsibility for range reductions or malfunctions caused by environ-
mental interference. The manufacturer's responsibility for damage caused to persons resulting from accidents of any nature caused by our defective
products, are only those responsibilities that come under Italian law.
6-1622135 REV.4 04/09/2006
Cancelling:
1. Press the hidden key "e" of the transmitter in order to activate the "learnig mode" of the unit. This operation
has the same result as pressing the learn button on the control unit but without having to open the control
unit.
2. Keep for some seconds the hidden key and the stored button of the transmitter to be cancelled
contemporarily pressed (f.i. "e" + "a" or "e" + "c")
LEGENDA LEGENDA LEGENDA LEGENDA
Press Key
ITA ENG FRA ESP DEU POR
Jumper open
Transmission
Jumper close
2/2