Troubleshooting Guide - Metabo RTD 18 LTX BL 30 Manual Del Usuario

en ENGLISH
E.g. remove the cutting line from the reel and
store in a bowl of water.
• Make sure that the machine does not have any
loose or damaged parts.
If necessary:
- Replace damaged parts.
- Tighten the screws.
- If necessary, have them repaired in a specialist
workshop.
• Store the machine in a dry place.
• Ensure that children cannot get anywhere near
the machine.
• For space-saving transport or storage, the rod
can (1) can be disassembled into two parts. See
chapter 6.1.
• Secure in a safe position for transport.
9. Maintenance
WARNING! Remove battery pack (9).
Unintentional startup can cause serious
injuries. The machine must be stationary.
WARNING! Danger of injury from sharp
cutting edge on the line cutter (12). Wear
protective gloves.
9.1 General maintenance
• Check the machine for damaged, missing or
loose parts such as screws, nuts, bolts and caps
before each use.
• Check the machine before each use for damage
and ageing and have it repaired in a specialist
workshop immediately if necessary.
• Tighten all fasteners and caps properly.
• Clean the machine with a dry cloth. Do not use
water.
• Never service damaged battery packs.
Service of battery packs should only be
performed by the manufacturer or authorized
service providers.
9.2 Replacing cutting line
See chapter 6.4.
Order number see chapter 11.
9.3 Lubrication
Lubrication is not required.

10. Troubleshooting Guide

One LED of the capacity display (10) flashes.
Battery pack empty.
- Charge battery pack.
Machine emits a lot of noise.
Cutting line is too short.
- Readjust cutting line (see chapter 7.5)
All LEDs of the capacity and signal display (10)
flash.
Overload.
- Let the machine cool down.
- Move forward more slowly.
18
The machine does not start.
The battery pack performance is weak.
- Charge battery pack.
The machine vibrates heavily.
The cutting line (16) is not the same length on both
side.
- Readjust the cutting line. See chapter (7.5).
The machine stops during the mowing
process.
Battery pack empty.
- Charge battery pack.
There is a blockage.
- Remove battery pack (9). Check the line head
(14).
The operating temperature of the machine is too
high.
- Let the machine cool down.
11. Accessories
Use only original Metabo or CAS (Cordless Alliance
System) battery packs and accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
A Cutting line Ø 2 mm, spiral-shaped (as spare)
Order no.: 628423000
B Cutting line Ø 2 mm, wave-shaped
Order no.: 628430000
C Complete line head (complete housing incl. reel
and cutting line, (as spare)
Order no.: 628429000
D Shoulder strap (as spare)
Order no.: 628427000
E Back carry strap
Order no.: 628428000
F Battery packs with different capacities. Buy
battery packs only with voltage suitable for your
power tool.
Order no.: 625367000
Order no.: 625368000
Order no.: 625369000
Order no.: 625549000
etc.
Order no.: 625027000
Order no.: 625028000
etc.
G Chargers: ASC 55, ASC 145, etc.
For a complete range of accessories, see
www.metabo.com or the catalogue.
12. Repairs
Repairs to electrical tools must only be carried
out by qualified electricians and only with
original spare parts!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
4.0 Ah (LiHD)
5.5 Ah (LiHD)
8.0 Ah (LiHD)
10.0 Ah (LiHD)
4.0 Ah (Li-Ion)
5.2 Ah (Li-Ion)