User Interface; Programming Commands - LiftMaster PPWR Guia De Inicio Rapido

USER INTERFACE

The PPWR user interface consists of a 22 character by 5 line LCD display, 3 "soft keys", Down/Up arrows and a numeric keypad.
Scroll Indicator
If more than 3 options exist, a scroll indicator appears on the
left margin of lines 2, 3, and 4. The scroll indicator shows the
relative position within the list.
Line 1:
Menu and function mode.
Lines 2, 3, and 4:
Menu selections and data.
Line 5:
Soft key function modes.
Backup memory module indicator
®
(LiftMaster logo screen only)

PROGRAMMING COMMANDS

The table below describes the commands used to program the receiver.
MAIN MENU
26 BIT (DEFAULT)
WIEGAND FORMAT
30 BIT
31 BIT
34 BIT EVEN
34 BIT ODD
50 BIT
BUTTON 1 IS ON
BUTTON FILTER
BUTTON 2 IS ON
BUTTON 3 IS ON
PASS THRU (DEFAULT)
MODE SELECT
ADVANCED
PROGRAM
SECURITY TABLE
If ADVANCED MODE is
turned off this option is
disabled and will appear
as NOT AVAILABLE FOR
LIST
PASS THRU MODE
PIN
SETTINGS
DEALER INFO
FIRMWARE VERSION
BEEP
MEMORY
CONTRAST
LANGUAGE
FACTORY DEFAULT
COMMAND
CHANGE FC OUT
DELETE
DUPLICATE MEMORY
RESTORE MEMORY
DESCRIPTION
26 Bit Wiegand output code.
30 Bit Wiegand output code.
31 Bit Wiegand output code.
34 Bit EVEN Wiegand output code.
34 Bit ODD Wiegand output code.
50 Bit Wiegand output code.
Used when multiple receivers are within range of each other. Button filter selects which
button the PPWR receiver responds to. Used in areas where of overlapping receiver
coverage. Default setting is: Button 1,2,3 ON.
Passes all received remote control signals to the access system host controller.
Receiver only passes signals from a remote control with a previously programmed facility
code. All other remote control facility codes are blocked.
Learn a facility code from any remote control in a batch that the PPWR will respond to.
Also used to resolve any conflicts in code translation.
NOTE: Once Advanced Mode is enabled, Facility Codes of all remote controls to be used
on site must be added to the Security Table.
Displays a list of all programmed facility codes showing facility code conflicts and facility
code changes. Options to delete or resolve facility code conflicts. Security Table can hold
up to 64 entries. MAX FC and FC IN > FC OUT entries can be configured to translate FC IN
to a specified FC OUT. Each FC IN can only have one FC OUT.
Change the 6-digit PIN number for the receiver.
Display and edit the dealer 10-digit phone number.
Displays the current firmware version.
Turn the audible feedback on or off.
This function creates a complete backup of programmed remote controls, and Security
Table settings. The backup may be restored to a replacement PPWR or used to copy the
configuration into other PPWR
Creates a memory backup. A memory module must be installed.
Restores a memory backup from a memory module. An indicator appears on the
®
LiftMaster logo screen if a backup memory module is installed.
NOTE: Content of memory module will over-write any information already stored in the
receiver memory. Remove memory module after backing up for safe keeping.
Press Down or Up arrows to adjust LCD contrast.
Sets language: English (Default), Spanish, and French.
Reset receiver settings to factory default. NOTE: If a PIN is set and lost the Reset Pin
function must be used to unlock the PPWR unit.
2
Antenna Connection
For the direct antenna or the
antenna extension kit.
Menu/Data selection shown
in inverse font.
LCD Screen
System programming and status
display.
"SOFT" Keys
Soft key functions are defined by
the label on line 5 of the display.
The functions change according
to the menu selection.
Down/Up Keys
For navigation in the menus.
Numeric Keypad
Numeric data is entered
through the numeric keypad.
Insert wiring