American Standard R110 Instrucciones De Instalación

ROUGH VALVE KIT
JUEGO DE V VULA SIN ACABADO
Á
ENSEMBLE DE ROBINET ROBUSTE
PRESSURE BALANCE TEMPERATURE CONTROL VALVE
VÁLVULA DE CONTROL DE TEMPERATURA CON EQUILIBRO DE PRESIÓN
ROBINET MITIGEUR
Thank you for selecting American-Standard...the benchmark of fine
quality for over 100 years. To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
Gracias por seleccionar los productos American Standard, sinónimo de la mejor calidad
durante más de 100 años. Por favor lea estas instrucciones detenidamente antes de
comenzar para que lleve a cabo la instalación sin contratiempos.
Nous vous remercions d'avoir choisi American Standard... synonyme de qualité supérieure
depuis plus de 100 ans. Pour vous assurer que l'installation se déroulera sans difficulté,
veuillez lire attentivement ces instructions avant de commencer.
ROUGHING-IN DIMENSIONS
To assure proper positioning in relation to wall, note roughing-in dimensions.
Tome nota de las dimensiones de desbastado para asegurar la posición correcta respecto de la pared.
Pour garantir un bon positionnement par rapport au mur, tenir compte des dimensions de préparation.
FINISHED WALL
PARED TERMINADA
PAROI FINIE
"SEE ILLUSTRATION"
"VEA LA FIGURA"
"VOIR ILLUSTRATION"
18" OPTIONAL
OPTATIVO, 18" (45,7 cm)
OPTION 45,7 cm (18 po.)
TOP OF TUB RIM
4"
BORDE SUPERIOR
DE LA BAÑERA
HAUT REBORD
BAIGNOIRE
BOTTOM OF TUB
FONDO DE LA BAÑERA
FOND BAIGNOIRE
1
ROUGHING-IN
When soldering, remove PLASTER GUARD, CARTRIDGES and CHECK STOPS (IF PRESENT). When finished soldering,
NOTE
flush valve body, replace cartridges, check stops (if present) and plaster guard to continue installation. Use thread
sealant or Teflon tape on threaded connections.
See Roughing-in diagram before starting.
Connections are:
1/2" copper sweat for sweat inlets
1/2" female NPT for threaded inlets
Connect RISER PIPE (1) to MANIFOLD (2)
top outlet marked "SHR".
Connect TUB FILLER PIPE (3) at bottom
outlet marked "TUB".
For proper positioning the finished wall
must be within side wall of PLASTER
GUARD (4).
Installation Instructions
Instrucciones de instalación
Mode d'installation
R110, R110BP, R110SS, R110SSBP
R115, R115BP, R115SS, R115SSBP
DIMENSIONES DE DESBASTADO
1-5/8" TO 3-1/4"
1-5/8" A 3-1/4" (41 MM A 83 MM)
41 mm (1-5/8 po.) À 83 mm (3-1/4 po.)
1/2" NPT
1/2" (12,7 MM) NPT
NPT 12,7 mm (1/2 po.)
OPTIONAL TO FINISHED FLOOR
USUALLY BETWEEN 65'' AND 78''
OPTATIVO AL PISO TERMINADO,
POR LO GENERAL ENTRE
OUTLETS 1/2" NPT
65" Y 78" (165 A 198 cm)
SALIDA, 1/2"
DISTANCE ENTRE OPTION ET
(12,7 mm) NPT
PLANCHER FINI ENTRE
ORIFICE 12,7 mm
165 cm ET 198 cm (65 à 78 po.)
(1/2 po.)
OUTLETS 1/2" NPT
SALIDA, 1/2"
(12,7 mm) NPT
ORIFICE 12,7 mm
(1/2 po.)
3-3/8"
(86 mm)
1/2" NPT
1/2" (12,7 MM) NPT
THREADED INLETS (STOPS)
NPT 12,7 mm (1/2 po.)
ENTRADAS ROSCADAS (LIMITADORES)
1/2" COPPER
ENTRÉES FILETÉES (BUTÉES)
1/2" (12,7 mm)
COBRE
12,7 mm
(1/2 po.) CUIVRE
CAUTION
Turn off water at main supply.
If the valve is installed on a fiberglass
or other thin wall application, the
PLASTER GUARD (4) can be used as a support.
Cut a 3" dia. hole in the shower stall.
If STOPS are used, drill two additional
1" holes to allow access to the stops.
Remove PLASTER GUARD (4), rotate 180˚
so that indicated screw holes fit MANIFOLD (2).
Push CAP on valve, place ESCUTCHEON on and
attach with screws.
Connect hot and cold water supplies.
Cap off shower pipe (5) and tub filler pipe (6).
For support, use pipe BRACES (7) secured to wooden braces.
With valve turned off, turn on water supplies.Check for leaks.
DIMENSIONS DE PRÉPARATION
INLETS 1/2" NPT
ENTRADAS, 1/2"
(12,7 mm) NPT
ENTRÉES 12,7 mm
(1/2 po.)
3-3/8"
(86 mm)
3-3/8"
(86 mm)
THREADED INLETS
ENTRADAS ROSCADAS
ENTRÉES FILETÉES
OUTLETS 1/2" NOM.
COPPER SWEAT
SALIDA, 1/2" (12,7 MM)
NOM. COBRE SOLDADO
ORIFICE CUIVRE LISSE
12,7 mm (1/2 po.) NOM.
5-7/8"
INLETS
(149 MM)
1/2" NPT
ENTRADAS, 1/2"
(12,7 MM) NPT
ENTRÉES NPT
12,7 mm (1/2 po.)
Certified to comply with ANSI A112.18.1
Cumplimiento certificado de los requisitos
de la norma ANSI A112.18.1
Certifié conforme à ANSI A112.18.1
U.S. Patent No. D403,750
Patente estadounidense D403,750
Brevet USA no. D403.750
OUTLETS 1/2" NOM.
COPPER SWEAT
SALIDA, 1/2" (12,7 MM)
NOM. COBRE SOLDADO
ORIFICE CUIVRE LISSE
12,7 mm (1/2 po.) NOM.
INLETS 1/2" NOM.
4-1/16"
COPPER SWEAT
(103 MM)
ENTRADAS, 1/2" (12,7 MM)
NOM. COBRE SOLDADO
ENTRÉES CUIVRE LISSE
12,7 mm (1/2 po.) NOM.
SWEAT INLETS
ENTRADAS SOLDADAS
ENTRÉES LISSES
5-7/8"
INLETS 1/2" NOM.
(149 MM)
COPPER SWEAT
ENTRADAS, 1/2" (12,7 MM)
NOM. COBRE SOLDADO
ENTRÉES CUIVRE LISSE
4-1/16" 12,7 mm (1/2 po.) NOM.
(103 MM)
SWEAT INLETS (STOPS)
ENTRADAS SOLDADAS (LIMITADORES)
ENTRÉES LISSES (BUTÉES)
5
7
HOT
4
M 9 6 8 3 8 2 A
4-1/16"
(103 MM)
1
2
COLD
PLUG
3
6