Cequent Towing Products 3360 Instrucciones De Instalación

Spring bar
Trailer
coupler
32" MAXIMUM
Shown In Proper Position
Using a Pro series SC WD kit
3" MIN.
7" MAX.
Note: A steel spacer block must be used
to eliminate gap between bolt & trailer tongue
for non-standard size Trailer frames.
1
Qty. (1) Cross channel
2
Qty. (4) Hex Bolt, ½-13 x 1.50 Lg. GR5
3
Qty. (8) Conical Toothed Washer, 1/2
4
Qty. (2) Angle Bracket
APPLICATION: This adapter is designed to be used as a mounting platform used with Cequent Towing Products Weight
Distributing Round bar, Trunnion bar (square) or Pro Series SC WD kits up to 1400 pounds maximum tongue weight.
1. Center the cross channel (1) on the trailer tongue approximately 29" rearward from the center of the coupler. This
dimension will vary depending on the model of WD system used.
NOTE: Please refer to your WD kit's installation instructions for specific dimensions and set up information.
2. Loosely attach the (2) angle brackets (item 4) to the cross channel using the 1/2" x 1.50 hex bolts, conical toothed
washers, and hex lock nuts as shown.
3. Slide the angle brackets (item 4) tight against side of trailer tongue. Tighten all (4) four 1/2 x 1.50 hex bolts.
4. Install the 3/8 x 5.5" long hex bolts and flat washers through the appropriate hole in angle bracket so that the bolts are
directly under the trailer tongue. Loosely install the flat washers and hex lock nuts onto bolts.
5. If necessary, adjust the fore/aft location of the cross channel to match your WD systems specifications
Do not exceed the 32" maximum set up dimension shown above.
6. Install the lift units (frame brackets) following your weight distributing system's hook-up procedure.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2007 Cequent Towing Products
Installation Instructions
POLE TONGUE ADAPTER
Lift unit
(frame bracket)
2
3
3
8
4
2" MIN
4" MAX.
Tighten all 3/8 GR5 fasteners with torque wrench to 30 Lb.-Ft. (41 N*M)
Tighten all 1/2 GR5 fasteners with torque wrench to 80 Lb.-Ft. (108 N*M)
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Pole Tongue Trailer Adapter
Trailer tongue
5
Qty. (2) Hex Lock Nut, 3/8-16
6
Qty. (2) Hex Bolt, 3/8-16 x 5.5 Lg. GR5
7
Qty. (4) Flat Washer, 3/8
Qty. (4) Hex Lock Nut, ½-13
Sheet 1 of 3 3360N
Part Number:
3360
Max Gross Max Tongue
Trailer WT (LB)
14,000 (6349kg.) 1400 (635 kg.)
Equipment Required:
Fastener Kit: 3360F
Wrenches: 9/16, 3/4, Torque Wrench
4-23-07
Form: F205 Rev A 5-6-05
WT (LB)
1
6
7
7
5
Rev. A