Shuttle DH110 Serie Guía Rápida

DH110 Series Quick Guide
More information on this product can be found at: http://bit.ly/DH110
更多本產品資訊 , 請蒞臨：http://bit.ly/DH110
Weitere Informationen zu diesem Produkt finden Sie unter: http://bit.ly/DH110
Pour plus d'informations sur ce produit, visitez: http://bit.ly/DH110
Product Overview
產品外觀 \ Produktübersicht \ Présentation du produit \ Resumen del producto \ 製品概要 \ 제품 설명 \ 产品外观
5 6
1 2 3 4
18 16
9 10 11 12 13
Hardware Installation
硬體安裝 \ Hardware Installation \ Installation du matériel \ Instalación de hardware \ ハードウェアのインストール \ 硬件安装
A. Begin Installation
For safety reasons, please ensure that the power cord is disconnected before opening the case.
!
1. Unscrew the two screws of the chassis cover.
Slide the cover backwards and upwards.
c
b
The product's colour and specifications may vary from the actually shipping product.
L
B. CPU and ICE Module Installation
1. Unfasten the four ICE module attachment screws and
unplug the fan connector. Remove the ICE module from
the chassis and put it aside.
b
c
a
 Follow the steps below to correctly install the CPU into
the motherboard CPU socket.
This CPU socket is fragile and can easily be damaged.
!
Always use extreme care when installing a CPU and
limit the number of times you remove or change the
CPU. Before installing the CPU, make sure to turn
off the computer and unplug the power cord from the
power outlet to prevent damage of the CPU.
2. Unlock and raise the socket lever.
a
3. Lift the metal load plate on the CPU socket.
DO NOT touch the socket contacts. To protect the
!
CPU socket, always use the protective socket cover
when the CPU is not installed.
快速安裝指南 Kurzanleitung Guide rapide Guía rápida クイックガイド 설치 가이드 快速安装指南
Puede encontrar más información sobre este producto en: http://bit.ly/DH110
本製品の詳細な情報については、次の URL より確認頂けます。http://bit.ly/DH110
更多本产品信息 , 请访问：http://bit.ly/DH110
7 8
1. MIC-in
2. Headphones
3. Power LED
4. HDD LED
5. Power Button
6. SD Card Reader
7. USB 3.1 Gen 1 Ports
8. USB 2.0 Ports
9. Power Jack (DC IN)
17 18
10. HDMI Port
11. DisplayPort
12. eSATA+USB 2.0 Combo
13. LAN Ports
14. PS/2 Port
15. Clear CMOS & Power Button
16. COM 1 Port (RS232/RS422/RS485)
17. COM 2 Port (RS232 only)
14
7 15
18. Kensington ® Lock Hole
2. Unfasten the rack mount screw and remove the rack.
b
a
4. Please orientate the CPU correctly and align the CPU
notches with the socket alignment keys. Make sure the
CPU sits perfectly horizontal, then push it gently into the
socket.
Align the CPU notches with
the socket alignment keys.
Triangle Pin1 Marking on the CPU
Please be aware of the CPU orientation, DO NOT
!
force the CPU into the socket to avoid bending of pins
on the socket and damage of CPU!
5. Tear off the protective membrane from the metal load
plate. Close the metal load plate, lower the CPU socket
lever and lock in place.
b
a
Tear off the protective membrane
6. Spread thermal paste evenly on the CPU surface.
Thermal Paste
application area
! Please do not apply excess amount of thermal paste.
7. Screw the ICE module to the motherboard. Note to
press down on the opposite diagonal corner while
tightening each screw.
8. Connect the fan.
f
C. Memory Module Installation
This motherboard does only support 1.35 V DDR3L
!
SO-DIMM memory modules.
1. Locate the SO-DIMM slots on the motherboard.
2. Align the notch of the memory module with the one of
the relevant memory slot.
SO-DIMM slot
a
3. Gently insert the module into the slot in a 45-degree
angle.
4. Carefully push down the memory module until it snaps
into the locking mechanism.
b
53R-DH1103-2301
E. HDD or SSD Installation
1. Place an HDD or SSD in the rack and secure with
the four screws from the sides.
b
F. Complete
1. Please replace and affix the case cover with two screws,
then connect the power cord.
2. Complete.
f
b
Please press the "Del" key while booting to enter
!
BIOS. Here, please load the optimised BIOS settings.
c
Safety Information
Incorrectly replacing the battery may damage this computer. Replace only with the same or equivalent as recommended by Shuttle.
!
Dispose of used batteries according to the manufacturer's instructions.
更換電池方式錯誤可能會損壞本電腦以及引發爆炸、火災或其他危險。僅能依 Shuttle 的建議 , 以相同或同等的電池更換。
請依照製造商的使用說明處理廢電池。
Das unkorrekte Austauschen der Batterie kann diesen Computer beschädigen. Ersetzen Sie die Batterie nur durch den von Shuttle empfohlenen
Typ oder ein gleichwertiges Modell. Entsorgen Sie gebrauchte Batterien gemäß den Herstellerangaben.
Ne pas replacer correctement la pile peut endommager l'ordinateur. Remplacez-la uniquement par un modèle identique ou un équivalent comme
recommandé par Shuttle. Débarrassez-vous des piles usagées d'après les instructions du constructeur.
La sustitución incorrecta de la batería puede dañar este equipo. Sustituya la batería únicamente por una igual o equivalente recomendada por
Shuttle. Deseche las baterías usadas según las instrucciones del fabricante.
バッテリを間違ってセットすると、こ a のコンピュータが損傷する原因となります。交換する際は、Shuttle が推奨するバッテリと同じものまた
は同等のものだけを使用するようにしてください。使用済みバッテリは、メーカーの指示に従って処分してください。
배터리를 잘못 교체할 경우 컴퓨터에 손상이 갈 수 있습니다 . 셔틀에 의하여 원래 장착한 것과 동일한 제품만을 사용하십시오 . 사용한 배터리의
폐기는 배터리 제조업체의 지시에 따르십시오 .
更换电池方式错误可能会损坏本电脑。仅能依 Shuttle 的建议 , 以相同或同等的电池更换。请依照制造商的使用说明处理废电池。
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device meets the requirements for the EU conformity in accordance to the currently valid EU directives.
Dieses Produkt erfüllt die Anforderungen für die EU-Konformität entsprechend der aktuell geltenden EU-Richtlinien.
Ce produit répond aux exigences de la conformité UE suivant les directives européennes actuellement en vigueur.
All bundled parts, included power cord, cannot use without this product.
電源ケーブル等、すべての付属品は本機以外ではご使用になれません。
5. Repeat the above steps to install an additional memory
module, if required.
D. M.2 Device Installation
a
1. Locate the M.2 key slots on the motherboard, unfasten
the screw first.
2. Install the M.2 device into the M.2 slot and secure with
the screw.
M.2 2242/2260 M key slot

Notch
Cutout
M.2 2230 A,E Key slot

a
45-degree
angle
2. Slide the rack back into the chassis and refasten the
screws. Connect the Serial ATA cable to the HDD or SSD.
a
Serial ATA cable
d
e
安 全 資 訊 \ Sicherheitshinweise \ Informations de sécurité \ Información de seguridad
安全に関する情報 \ 안전 정보 \ 安全信息
Latch Latch
b
a
Slope angle
c
b
a
Slope angle
c
b
a
c
a
c
b
DC-IN