Technical Data - USAG 889 KA Manual De Instrucciones

USAG 889 KA
ENGLISH

TECHNICAL DATA

Power supply and power output as stated on the model nameplate - Double insulation – IP65
Manufactured in compliance with EN 60598:2008-10/A11:2009-05 and EN 60592-2-8:1997-05/A1:2000-06/A2:2008-02 standards.
INSTALLATION
- NOTE: before using the lamp carefully read the following instructions. - Ensure that the lamp can be disconnected from the electrical supply in case
of emergency.
ELECTRICAL CONNECTION
- Make sure that the portable lamp power supply matches the system power supply - Use the lamp in places prescribed and designated by current
regulations regarding the workplace and electrical systems - Check that the plug on the cable is appropriate to the particular workplace; replace if
necessary - If the lamp is supplied without cable, fit appropriate cable and plug in accordance with current regulations - The wiring should be carried
out by qualified personnel, according to the following instructions.
OPERATING INSTRUCTIONS
- Insert the plug in an appropriate socket - Use the switch to switch on and off - Always check that the device is in full working order and shows no
safety risks - Do not remove the protection guards - Do not open the device: maintenance should be carried out by qualified personnel - Before
replacing the bulb disconnect the lamp from the electrical supply - If the feeder cable is damaged it should be replaced immediately with another of
the same type at an authorised after-sales centre or by a qualified electrician.
BULB REPLACEMENT INSTRUCTIONS
a – Remove the ring nut locking screw (detail K).
b – Remove ring nut 1
c – Extract housing 2 as far as allowed by the safety cable
d – Screw the bulb 4 (E27) inside handle 3 housing
e – Refit housing 2 verifying the correct positioning of the gasket (detail J)
f – Fit ring nut 1 and tighten the locking screw (detail K)
- Do not tamper with the safety devices (ring nut locking screw and safety cable)
IF THE DEVICE DOES NOT WORK
- Check that the voltage of the portable lamp is working efficiently and matches the system voltage - Check that there is power at the socket - Check
the operation of the switch: that is, that it switches properly both ways - If the device continues not to work contact a specialised repair centre.
ACCESSORIES AND SPARE PARTS
Use only accessories and spare parts approved by the manufacturer.
- fluorescent bulb
E27
GENERAL PRECAUTIONS
The components have been chosen and used keeping in mind the working conditions and life-span of the lamp. Install the lamp so that it presents no
danger to personnel as long as it is used correctly. No protection or warning will ever be sufficient if the person fails to take certain precautions, if the
lamp is not kept in perfect working order, or if the following recommendations are not followed. Learn the correct use before starting work. Check that
those using the lamp know how it works and use it safely. Avoid exposing yourself and others to unnecessary risks. Do not remove, adjust or obstruct
the SAFETY DEVICES put in place by the manufacturer, and ensure that they are not removed or rendered less effective. Keep the workplace free of
tools and any unnecessary objects.
centre. Work done by unauthorised persons will invalidate every type of warranty.
This appliance must not be used by people (including children) with physical, sensory or mental disabilities, or who have not been supervised or
trained to use the appliance by a person responsible for their safety. Children must be supervised to ensure they do not play with the appliance.
WARRANTY
- 12 months from the purchase date - The warranty consists in free repair or replacement by us of parts which, in our opinion, are materially or
operationally defective - Any other form of compensation is excluded - Repair or replacement of parts subject to wear and tear is excluded -
Transportation expenses will be borne by the buyer - The warranty is not applicable if the device is damaged due to negligence.
Implementing European directives 2002/95/EC, 2002/96/EC and 2003/108/EC - (Waste Electrical and
The crossed out waste bin symbol shown above means that this piece of equipment must be disposed of separately.
Therefore, this product must not be disposed of as ordinary urban waste once it reaches the end of its life. The product must
be disposed of in the special collection systems provided for this type of product, or by returning it to the distributor when
purchasing a new product of the same type. By ensuring that this product is disposed of correctly, and by avoiding it is
misused, a negative impact on the environment and on people is avoided, as the product contains potentially harmful
substances. This product must be disposed of in compliance with current waste legislation, in order to avoid all the
sanctions implemented when such waste (WEEE) is disposed of illegally.
SWK Utensilerie Srl
Via Volta, 3 – 21020 Monvalle (VA)
Tel. +39 0332 790111 – Fax +39 0332
790330
info.mv@usag.it –
PORTABLE LAMP - SAFETY INSTRUCTIONS
In the event of having to do work on the portable lamp (excepting replacement of the bulb), contact an after-sales
Electronic Equipment – WEEE).
www.usag.it
CABLE FITTING INSTRUCTIONS
(B1) – Insert the cable in the handle hole
(B2) – Connect the cable to the circuit, taking into account the length of the
stripped cable and fit the cable holder
(B3) – Insert the circuit in the handle
(B4) – Tighten the locking screws and the safety cable connected to the housing
- Assemble as described in steps e-f of the bulb replacement instructions
Cable must be 2x1 mm² - H05 RN-F
The installation of the cable must be performed by qualified
personnel.