Frigidaire FARE4044MW Manual De Instrucciones

WARNING
• Dryer must be properly grounded at all times.
• Vent dryer through free-fl owing, outdoor-vented, metal duct system.
• Improper gas installation or LP conversion could result in injury or even death.
• Avoid back or other injury. Use more than one person to move, lift or tip the dryer.
UNPACKING & HANDLING
A)
EMPTY DRUM
CONTENTS
B)
CAREFULLY
TIP
PROTECT
FLOOR
C)
REMOVE & SAVE
D)
RETURN
UPRIGHT
HEAT SOURCE
GAS DRYER
WRENCH-TIGHT
APPLY APPROVED THREAD SEALANT.
REFER TO INSTALLATION
INSTRUCTIONS FOR MORE DETAILED
INFORMATION.
MANUAL SHUTOFF
ELECTRIC DRYER
30 AMP
DON'T MOVE
INSTALL
U.L.-APPROVED
STRAIN RELIEF
OPERATE
Turn or push in to
power up dryer.
POWER UP
DRYER
3 beeps = 2 beeps =
STATUS
dryer power up cycle pause
INDICATOR
BEEPS
Push in to start cycle.
Push in to pause cycle.
START/PAUSE
DRYER
IMPORTANT
Please read all safety instructions before using your
new dryer. For best drying results with your new
dryer, remember to review:
INSTALLATION INSTRUCTIONS
USE & CARE GUIDE
CART FROM REAR
2-PERSON CARRYING
ONLY WITH 7" (MIN.) STRAPS, FRONT-TO-
CART FORKS BACK RECOMMENDED
DO NOT USE KNEE
DO NOT CART
DO NOT CART
IN CABINET SIDE
FROM FRONT FROM SIDE
TO MOVE UNIT
DO NOT USE OPEN
DO NOT USE REAR CONSOLE TO PUSH,
DOOR TO LIFT OR
PULL, TIP OR MOVE THE DRYER.
TIP THE UNIT
LEVEL & CONNECT
L.P. SYSTEMS MUST USE
COVERSION KIT INSTALLED
BY QUALIFIED TECHNICIAN.
30 AMP
WHITE
MOVE GROUND
GREEN
RED OR
RED OR
BLACK
BLACK
1 beep =
cycle start
Leave these instructions
with the customer.
VENT EXHAUST
• USE ONLY 4 INCH (10.2 CM) RIGID METAL OR SEMI-
RIGID METAL DUCTING
• REPLACE PLASTIC OR FOIL DUCTS WITH METAL
• CLEAN LINT FROM PRESENT DUCT SYSTEM BEFORE
ADDING ON
• SEE CHART TO THE RIGHT FOR ACCEPTABLE NUMBER
OF 90° TURNS IN SYSTEM
• DO NOT USE SCREWS TO CONNECT DUCTS
• DO NOT USE REGULAR DUCT TAPE TO CONNECT DUCTS,
ONLY METAL FOIL TAPE
• 4" (10.2 cm) CLAMP RECOMMENDED FOR
CONNECTION BETWEEN DRYER & EXHAUST SYSTEM
• EXHAUST SYSTEM MUST BE VENTED OUTSIDE WITH
APPROVED VENT HOOD
• TO VENT LEFT OR RIGHT FROM DRYER, USE 90°
QUICK-TURN ELBOW
• FOR INSTALLATION IN A RECESSED AREA OR CLOSET,
SEE COMPLETE INSTALLATION INSTRUCTIONS
• FOR MOBILE HOME INSTALLATION, SEE COMPLETE
INSTALLATION INSTRUCTIONS
lower
raise
A)
ADJUST
D)
CONNECT
POWER
CAUTION
ELECTRICAL SHOCK HAZARD
Do NOT use prong adapter.
Do NOT remove ground prong.
Do NOT use extension cord.
THE EXHAUST SYSTEM SHOULD BE INSPECTED
AND CLEANED A MINIMUM OF EVERY 18 MONTHS
WITH NORMAL USAGE. THE MORE THE DRYER IS
USED, THE MORE OFTEN YOU SHOULD CHECK
THE EXHAUST SYSTEM AND VENT HOOD FOR
PROPER OPERATION.
CLEAN LINT FILTER
AFTER EVERY LOAD.
NOTE TO REMARQUE POUR
INSTALLER L'INSTALLATEUR
Laissez ces instructions au
client.
Suite de la version française au verso.
MAXIMUM LENGTH*
of 4" (10.2cm) Rigid Metal Duct
VENT HOOD TYPE
(Preferred)
4"
(10.2cm) louvered
0 64 ft. (19.5 m)
1 52 ft. (15.9 m)
2 44 ft. (13.5 m)
3 36 ft. (11.0 m)
4 28 ft. (9.5 m)
*Do not install plastic or foil ducting. If installing semi-rigid
ducting, do not exceed 8 ft (2.4 m) total duct length.
IMPORTANT
For closet installations see detailed installation instructions
enclosed.
B)
LEVEL BOTH WAYS
OPEN GAS VALVE AND
CHECK FOR LEAKS
WITH SOAPY WATER
E)
DRYNESS LEVEL (IF EQUIPPED)
SELECTABLE IN AUTO DRY CYCLES ONLY
Damp Dry (on select models)
Low
Normal Dry
High
Max (on select models)
NOTA AL
INSTALADOR
Deje estas instrucciones
con en cliente.
Español continua en la pagina trasera.
2.5"
(6.35cm)
CORRECT
48 ft. (14.6 m)
40 ft. (12.2 m)
32 ft. (9.8 m)
24 ft. (7.3 m)
16 ft. (4.9 m)
INCORRECT
C)
CHECK STABILITY,
CORNER-TO-CORNER
137542900A (1204)