IK Multimedia iLoud Guia De Inicio Rapido página 5

meters (33 feet) from iLoud.
I have connected my guitar to iLoud, but I can't hear
any sound from my instrument.
The instrument or microphone signal is NOT directly sent to
the iLoud speakers. To use the iRig input feature, you need
to connect an iOS device running AmpliTube, VocaLive or
another audio-processing app to the iLoud 1/8" input socket
(5) using the included 1/8" TRRS cable.
iLoud sounds too boomy.
Move iLoud away from the wall.
iLoud sounds too thin.
Position iLoud on a flat surface.
Sometimes iLoud stops playing, the sound is intermittent.
When used in very hot environments (for example in
direct sunlight during the summer), at very high volumes,
the iLoud power amps may go into protection mode. This
causes the sound to stop for a while and then to restart
again. To avoid this problem let iLoud cool down for a period
of time, or move it to a cooler location.
Specifications
• 40W total power (2x16W low-frequency, 2x4W high
frequency).
• Frequency response 50Hz to 20kHz.
• Four Class-D Amplifiers, bi-amped system.
• Two way 2x3" neodymium woofers & 2x3/4" neodymium
tweeters.
• High performance bass-reflex port.
• 1/4" iRig® input for connecting guitars and dynamic
microphones to iOS devices.
• Bluetooth compatible with A2DP protocol.
• 1/8" stereo analog line input.
• DSP controlled.
• Superior low-frequency extension and sound accuracy.
• Auto Standby.
• Integrated high-performance Li-Ion rechargeable battery.
• Battery duration at maximum volume: up to three hours.
Normal usage: up to ten hours.
Warranty
Please visit:
www.ikmultimedia.com/warranty
for the complete warranty policy.
Support and more info
www.ikmultimedia.com/support
FCC statement
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
FCC radiation exposure statement
This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed
and operated with minimum distance 20cm between the radiator &
your body.
IC statement/warning
CAN ICES-3(B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference
that may cause undesired operation of the device.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.