Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

1/16 Shock Rebuild Instructions
Shock Disassembly
(Use the shock exploded view included to aid in the assembly process.)
1. Remove the spring and lower spring retainer from the shock.
2. Remove the shock cap and empty the shock body of shock oil.
3. Use side cutters to grip the shock shaft just above the rod end.
Remove the rod end from the shock shaft.
4. Remove the lower cap from the shock body with a small flat blade
screwdriver. Slide the shock shaft with piston out of the shock body.
5. Remove the O-rings and spacer from the bottom of the shock body.
Shock Assembly
1. Replace the stock piston by removing the top E-clip above the
piston. Place new piston onto shaft, and ten secure it by reinstalling
the top E-clip.
2. Insert the shock shaft assembly through the shock body until the
piston bottoms out.
3. Lubricate the shaft and O-rings with silicone oil.
4. Install the one o-ring over the shaft and into the bore of the shock
body followed by one small black spacer, and then another o-ring.
5. Install the lower cap by pressing it onto the shock body until
it snaps on.
6. Grip the shaft close to the threads with needle nose pliers or side
cutters and thread the rod end onto the shock shaft until the rod
end bottoms out.
7. Fill the shock with new silicone shock oil up to the top of the shock
body. Slowly move the piston up and down (always keeping it
submerged in oil) to release the air bubbles. Let the shock sit for a
few minutes to allow any remaining air bubbles to surface.
8. Slowly thread the upper cap with the installed shock bladder onto
the shock body. The excess oil will bleed out of the small hole in the
shock cap. Tighten the shock cap until snug.
9. Reinstall the spring and lower retainer.
Traxxas, 1100 Klein Road, Plano, TX 75074, Phone: 972-265-8000, Fax: 972-265-8011, e-mail: support@Traxxas.com
Tools Needed:
• Needle nose pliers
• Small side cutters
• Small flat blade screwdriver
T RAXXA S. c o m
Covers Part #7061X, 7062
7028
7065
7062
7065
7062
7063
7063T
7066
7066X
7065
7145 Orange
7146 Green
7147 Tan
7148 Black
7140 Double Orange
7141 Double Green
7142 Double Tan
7143 Double Black
7062
7065
7062
KC1697-R00
7028
7065
7062
Rev 120810

Publicidad

loading

Resumen de contenidos para Traxxas 7061X

  • Página 1 The excess oil will bleed out of the small hole in the 7062 shock cap. Tighten the shock cap until snug. 9. Reinstall the spring and lower retainer. 7062 T RAXXA S. c o m Traxxas, 1100 Klein Road, Plano, TX 75074, Phone: 972-265-8000, Fax: 972-265-8011, e-mail: support@Traxxas.com KC1697-R00 Rev 120810...
  • Página 2 Serrez complètement le bouchon de l’amortisseur. 7062 9. Réinstallez le ressort et la coupelle d’appui du ressort inférieure. T RAXXA S. c o m Traxxas, 1100 Klein Road, Plano, TX 75074, Phone: 972-265-8000, Fax: 972-265-8011, e-mail: support@Traxxas.com KC1697-R00 Rev 120810...
  • Página 3 Ajuste la tapa del amortiguador 7062 hasta que quede firme. 9. Reinstale el resorte y el bloqueo inferior. TR AXXAS . c o m Traxxas, 1100 Klein Road, Plano, TX 75074, Phone: 972-265-8000, Fax: 972-265-8011, e-mail: support@Traxxas.com KC1697-R00 Rev 120810...
  • Página 4 Loch in der Stoßdämpferabdeckung heraus. Ziehen Sie die Stoßdämpferabdeckung von Hand an. 7062 7062 9. Installieren Sie die Feder und den Federteller wieder. TR AXXAS . c o m Traxxas, 1100 Klein Road, Plano, TX 75074, Phone: 972-265-8000, Fax: 972-265-8011, e-mail: support@Traxxas.com KC1697-R00 Rev 120810...

Este manual también es adecuado para:

7062