Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Universal speaker adapters for mounting
5 1/4" or 6 1/2" speakers to 6" x 8" locations
(tweeter provisions included)
KIT FEATURES
• Mounts 5 1/4" or 6 1/2" speaker to 6 x 8" location
KIT COMPONENTS
• A) Speaker adapter plates • B) (8) #8 X 1/2" Phillips screws • C) (8) Speed clips
A
B
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • Not required
TOOLS REQUIRED
• Phillips screwdriver • Cutting tool • Pliers
METRA. The World's best kits.
Installation instructions for 82-6901
82-6901
C
metraonline.com
™
Table of Contents
Kit Preparation ....................................................... 2
Kit Assembly .......................................................... 3
CAUTION!
Metra recommends disconnecting the negative bat -
tery terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your local
Dealership for more information. All accessories, switches, climate
controls panels, and especially air bag indicator lights must be con -
nected before reconnecting the battery or cycling the ignition. Also,
do not remove the factory radio with the key in the on position, or the
vehicle running. It would be best to remove the key from the ignition
and then wait a few seconds before removing the factory radio.
© COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION
Publicidad
Tabla de contenido
Manuales relacionados para Metra 82-6901
Resumen de contenidos para Metra 82-6901
- Página 1 • A) Speaker adapter plates • B) (8) #8 X 1/2” Phillips screws • C) (8) Speed clips CAUTION! Metra recommends disconnecting the negative bat - tery terminal before beginning any installation, unless the vehicle manufacturer recommends against so. Please check with your local Dealership for more information.
-
Página 2: Kit Preparation
82-6901 Kit Preparation 1. Mount the tweeter to the speaker adapter plate using the hardware supplied with the tweeter. (if the opening is too small, turn the adapter plate over and widen the opening by cutting along the scored lines. -
Página 3: Kit Assembly
82-6901 Kit Assembly 1. Locate the mounting positions where the speaker will be installed. (Figure A) 2. Mount the speaker assembly to the desired location with (4) #8 x 1/2” Phillips screws supplied. (To provide the necessary support, speed clips must be used on plastic mounting locations). -
Página 4: Important
Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians METRA. The World’s best kits. metraonline.com ™ © COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION... -
Página 5: Características Del Kit
Sería mejor retirar la llave de la ignición y esperar unos cuantos segundos antes de quitar el radio de fábrica. • Destornillador Phillips • Herramienta de corte • Alicates METRA. The World’s best kits. metraonline.com ™ © COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION... -
Página 6: Preparación Del Kit
82-6901 Preparación del kit 1. Monte la bocina de alta frecuencia en la placa adaptadora de la bocina usando los tornillos que vienen con la bocina de alta frecuencia. (Si la apertura es demasiado pequeña, voltee la placa adaptadora y ensanche la apertura cortando a lo largo de las líneas marcadas. -
Página 7: Ensamble Del Kit
82-6901 Ensamble del kit 1. Ubique las posiciones de montaje donde se instalará la bocina. (Figura A) 2. Monte el ensamble de la bocina en el lugar deseado con los (4) tornillos Phillips #8 de 1/2” suministrados. (Para proporcionar el soporte necesario, deben usarse ganchos de seguridad en los lugares de montaje de plástico). -
Página 8: Importante
800-354-6782 para obtener más información y avance hacia un futuro mejor. Metra recomienda técnicos con certificación del Programa de Certificación en Electrónica Móvil (Mobile Electronics Certification Program, MECP). METRA. The World’s best kits. metraonline.com ™ © COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION...