Assembly And Adjustments - DeWalt DCS551 Manual De Instrucciones

• Pull by the plug rather than the cord when disconnecting the charger. This will
reduce the risk of damage to the electric plug and cord.
• Make sure that the cord is located so that it will not be stepped on, tripped over or
otherwise subjected to damage or stress.
• Do not use an extension cord unless it is absolutely necessary. Use of improper
extension cord could result in risk of fire, electric shock or electrocution.
• When operating a charger outdoors, always provide a dry location and use an
extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces
the risk of electric shock.
• An extension cord must have adequate wire size (AWG or American Wire Gauge)
for safety. The smaller the gauge number of the wire, the greater the capacity of the cable,
that is, 16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in
line voltage resulting in loss of power and overheating. When using more than one extension
to make up the total length, be sure each individual extension contains at least the minimum
wire size. The following table shows the correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next heavier gauge. The lower the gauge number,
the heavier the cord.
Minimum Gauge for Cord Sets
Volts
Ampere Rating 120V
240V
More
Not More
Than Than
0 6
6 10
10 12
12 16
• Do not place any object on top of the charger or place the charger on a soft surface
that might block the ventilation slots and result in excessive internal heat. Place the
charger in a position away from any heat source. The charger is ventilated through slots in
the top and the bottom of the housing.
• Do not operate the charger with a damaged cord or plug.
• Do not operate the charger if it has received a sharp blow, been dropped or
otherwise damaged in any way. Take it to an authorized service center.
• Do not disassemble the charger; take it to an authorized service center when service
or repair is required. Incorrect reassembly may result in a risk of electric shock, electrocution
or fire.
• Disconnect the charger from the outlet before attempting any cleaning. This will
reduce the risk of electric shock. Removing the battery pack will not reduce this risk.
• NEVER attempt to connect 2 chargers together.
• The charger is designed to operate on standard 120V household electrical power.
Do not attempt to use it on any other voltage. This does not apply to the vehicular
charger.
Chargers
Your tool uses a D WALT charger. Be sure to read all safety instructions before using your charger.
E
Consult the chart at the end of this manual for compatibility of chargers and battery packs.
Charging Procedure (Fig. 2)
1. Plug the charger into an appropriate outlet before inserting the battery pack.
2. Insert the battery pack (G) into the charger, as shown in Figure 2, making sure the pack
is fully seated in charger. The red (charging) light will blink continuously, indicating that the
charging process has started.
3. The completion of charge will be indicated by the red light remaining ON continuously. The
pack is fully charged and may be used at this time or left in the charger.
Indicator Light Operation
DCB101
PACK CHARGING
PACK CHARGED
HOT/COLD DELAY
x
PROBLEM PACK OR CHARGER
PROBLEM POWERLINE
DCB107, DCB112
PACK CHARGING
PACK CHARGED
HOT/COLD DELAY
Charge Indicators
This charger is designed to detect certain problems that can arise. Problems are indicated by
the red light flashing at a fast rate. If this occurs, re-insert the battery pack into the charger. If the
problem persists, try a different battery pack to determine if the charger is working properly. If
the new pack charges correctly, then the original pack is defective and should be returned to a
service center or other collection site for recycling. If the new battery pack elicits the same trouble
indication as the original, have the charger and the battery pack tested at an authorized service
center.
HOT/COLD DELAY
DCB101
This charger has a hot/cold delay feature: when the charger detects a battery that is hot, it
automatically starts a delay, suspending charging until the battery has cooled. After the battery
has cooled, the charger automatically switches to the pack charging mode. This feature ensures
maximum battery life. The red light flashes long, then short while in the hot/cold delay mode.
DCB107, DCB112
The DCB107 and DCB112 chargers have a hot/cold delay feature. When the charger detects
a battery that is hot, it automatically delays charging until the battery has cooled. When the
charger detects a battery that is cold, it automatically delays charging until the battery has
warmed.
The red light will continue to blink, but a yellow indicator light will be illuminated during this
operation. Once the battery has cooled, the yellow light will turn off and the charger will resume
the charging procedure.
LEAVING THE BATTERY PACK IN THE CHARGER
The charger and battery pack can be left connected with the charge indicator showing Pack
Charged.
WEAK BATTERY PACKS: Weak batteries will continue to function but should not be expected
to perform as much work.
FAULTY BATTERY PACKS: This charger will not charge a faulty battery pack. The charger will
indicate faulty battery pack by refusing to light or by displaying problem pack or charger.
NOTE: This could also mean a problem with a charger.
PROBLEM POWER LINE
Some chargers have a Problem Power Line indicator. When the charger is used with some
portable power sources such as generators or sources that convert DC to AC, the charger may
temporarily suspend operation, flashing the red light with two fast blinks followed by a pause. This
indicates the power source is out of limits.
Wall Mounting
DCB107, DCB112
These chargers are designed to be wall mountable or to sit upright on a table or work surface.
If wall mounting, locate the charger within reach of an electrical outlet. Mount the charger
securely using drywall screws at least 1" (25.4 mm) long, screwed into wood to an optimal depth
leaving approximately 7/32" (5.5 mm) of the screw exposed.
Important Charging Notes
1. Longest life and best performance can be obtained if the battery pack is charged when the
air temperature is between 65 °F and 75 °F (18° – 24 °C). DO NOT charge the battery pack
in an air temperature below +40 °F (+4.5 °C), or above +105 °F (+40.5 °C). This is important
and will prevent serious damage to the battery pack.
2. The charger and battery pack may become warm to the touch while charging. This is a
normal condition, and does not indicate a problem. To facilitate the cooling of the battery
pack after use, avoid placing the charger or battery pack in a warm environment such as in
a metal shed or an uninsulated trailer.
3. A cold battery pack will charge at about half the rate of a warm battery pack. The battery
pack will charge at that slower rate throughout the entire charging cycle and will not return
to maximum charge rate even if the battery pack warms.
4. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp or other appliance;
b. Check to see if receptacle is connected to a light switch which turns power off when you
turn out the lights;
c. Move the charger and battery pack to a location where the surrounding air temperature
is approximately 65 °F – 75 °F (18° – 24 °C);
d. If charging problems persist, take the tool, battery pack and charger to your local service
center.
5. The battery pack should be recharged when it fails to produce sufficient power on jobs
which were easily done previously. DO NOT CONTINUE to use under these conditions.
Follow the charging procedure. You may also charge a partially used pack whenever you
desire with no adverse effect on the battery pack.
6. Foreign materials of a conductive nature such as, but not limited to, grinding dust, metal
chips, steel wool, aluminum foil, or any buildup of metallic particles should be kept away
from charger cavities. Always unplug the charger from the power supply when there is no
battery pack in the cavity. Unplug the charger before attempting to clean.
7. Do not freeze or immerse the charger in water or any other liquid.
WARNING: Shock hazard. Don't allow any liquid to get inside the charger. Electric shock
may result.
WARNING: Burn hazard. Do not submerge the battery pack in any liquid or allow any liquid
to enter the battery pack. Never attempt to open the battery pack for any reason. If the plastic
housing of the battery pack breaks or cracks, return to a service center for recycling.
Storage Recommendations
1. The best storage place is one that is cool and dry, away from direct sunlight and excess heat
or cold.
2. For long storage, it is recommended to store a fully charged battery pack in a cool dry place
out of the charger for optimal results.
NOTE: Battery packs should not be stored completely depleted of charge. The battery pack will
need to be recharged before use.
Total Length of Cord in Feet (meters)
25 (7.6) 50 (15.2) 100 (30.5)
50 (15.2) 100 (30.5) 200 (61.0)
AWG
18 16 16
18 16 14
16 16 14
14 12 Not Recommended
FIG. 1
F
C
B
150 (45.7)
300 (91.4)
FIG. 2
G
14
12
12
SAVE THESE INSTRUCTIONS FOR FUTURE USE
COMPONENTS (Fig. 1, 4)
WARNING: Never modify the power tool or any part of it. Damage or personal injury could result.
A. ON/OFF switch
B. Cutting depth guide
C. Collet nut
D. Collet lock button
E. Spindle lock button
INTENDED USE
This cut out tool is designed for professional cut out applications.
DO NOT use under wet conditions or in presence of flammable liquids or gases.
This cut out tool is a professional power tool. DO NOT let children come into contact with the tool.
Supervision is required when inexperienced operators use this tool.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal injury, turn tool off and remove the
battery pack before making any adjustments or removing/installing attachments or
accessories. An accidental start-up can cause injury.
Installing and Removing the Bit (Fig. 1)
This tool is designed for spiral cutting bits with either a 1/8" (3 mm) or 1/4" (6 mm) shank and
has a tool-free bit change system. To change bits, FIRST turn off the tool and disconnect the
battery from the tool. Remove the depth guide (B).
1. To replace bit, depress both spindle lock (E) and collet lock (D) and turn collet grip
counterclockwise.
2. Insert or remove bit.
The bits are sharp and should be handled with great care.
WARNING:
CAUTION: When replacing bits, do not insert cutting flutes into the collet. This may result in
broken bits.
3. While depressing both spindle and collet locks, turn the collet grip clockwise to firmly tighten
the collet. For some heavy duty applications, it may be necessary to use a wrench to further
tighten the nut (C) while depressing the spindle lock (E).
4. Attach guide.
CAUTION: Never tighten the collet without a bit installed.
This tool comes with both 1/8" (3 mm) and 1/4" (6 mm) collets. To change collets, remove the
collet nut and insert the desired collet.
Depth Guide (Fig. 1, 5)
Depth guide (B) snaps onto locators as shown. Keep depth guide in place at all times during operation
of the tool. For best results, adjust the guide using the knob to allow the bit to protrude about 1/8"
mm)
past the material to be cut.
OPERATION
To reduce the risk of serious personal injury, turn tool off and remove the
WARNING:
battery pack before making any adjustments or removing/installing attachments or
accessories. An accidental start-up can cause injury.
Installing and Removing the Battery Pack (Fig. 3)
NOTE: For best results, make sure your battery pack is fully charged.
To install the battery pack (G) into the tool handle, align the battery pack with the rails inside the
tool's handle and slide it into the handle until the battery pack is firmly seated in the tool and
ensure that it does not disengage.
To remove the battery pack from the tool, press the release button (I) and firmly pull the battery
pack out of the tool handle. Insert it into the charger as described in the charger section of this
manual.
FUEL GAUGE BATTERY PACKS (FIG. 4)
Some D WALT battery packs include a fuel gauge which consists of three green LED lights that
E
indicate the level of charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge button (J). A combination of the three green
LED lights will illuminate designating the level of charge left. When the level of charge in the battery
is below the usable limit, the fuel gauge will not illuminate and the battery will need to be recharged.
NOTE: The fuel gauge is only an indication of the charge left on the battery pack. It does not indicate
tool functionality and is subject to variation based on product components, temperature and end-user
application.
For more information regarding fuel gauge battery packs, please call 1-800-4-D
(1-800-433-9258) or visit our website www.dewalt.com.
To Maintain Safe Tool Control
•
Make sure the work surface is free of nails or screws.
cause the tool to jump, damaging the bit.
• Never operate the tool with one hand while holding the workpiece with the other hand.
Always clamp the material and guide the tool with both hands.
•
Do not cut material lying on a hard surface
allowed for protruding bit.
•
Disconnect battery from tool
• Do not start the tool with bit engaged in the material.
Switch (Fig. 1)
To start the motor, slide the switch (A) to "I" position. To stop the motor, slide the switch to "O" position.
Cutting a Hole for an Electrical Outlet (Fig. 5)
WARNING: Shut off all live electric circuits to any areas where cut outs will be ma
1. Push any wiring deeply into the outlet box to avoid damage from the cutting bit.
2. Before hanging the sheet covering the outlet, mark the approximate location of the center of the
outlet on the wall board. Check the cutting bit depth against the side of the board to be sure it
will cut entirely through the material.
3. Tack the sheet in place with a few fasteners avoiding the stud holding the outlet. This allows the
wall board to flex slightly around the protruding fixture box.
4. Turn the cut-out tool on. Holding the tool firmly with both hands, plunge the bit straight into the
center of the outlet.
5. Cut to the right until the edge of the box is touched. Pull out just enough for the bit to clear the
edge of the box. Plunge in again holding the bit gently against the outside of the box.
6. Follow the outside of the box as shown keeping slight pressure against the box. This will minimize
wandering and give you a clean precise cut.
7. Remove the waste and dust from the outlet. Finish fastening the sheet of wall board.
MAINTENANCE
WARNING: To reduce the risk of serious personal injury, turn tool off and remove the
battery pack before making any adjustments or removing/installing attachments or
accessories.
An accidental start-up can cause injury.
Cleaning
WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week. To
minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when performing this.
WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the
tool. These chemicals may weaken the plastic materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid get inside the tool; never immerse any part of the
tool into a liquid.
CHARGER CLEANING INSTRUCTIONS
WARNING: Shock hazard. Disconnect the charger from the AC outlet before cleaning. Dirt and
grease may be removed from the exterior of the charger using a cloth or soft non-metallic brush. Do
not use water or any cleaning solutions.
E
A
D
FIG. 3
FIG. 5
F. LED worklight
G. Battery Pack
H. Battery fuel gauge
I. Battery release button
. Clearance behind material to be cut must be
before making adjustments, changing bits, or cleaning tool.
The bit may grab the material.
G
I
H
FIG. 4
J
G
I
(3
WALT
E
Cutting into a nail or screw may
de.