Publicidad
Idiomas disponibles
Idiomas disponibles
English
WARNING: Carry out the installation in a "workmanlike" manner, strictly following the installation instructions and using
suitable tools. Always consult your local building department for code requirements that must be respected depending
on its destination of use (private, secondary, public...).
Before starting to assemble unpack each element of the staircase. Position them on an ample surface and check
the quantity of the elements (TAB. 1: A = Code, B = Quantity).
Preliminary assembly
1. Assemble the bushes D32 on the treads L02 with ring nut D33 and tighten manually. Insert components C13
and C31 in the bushes D32 (fig. 2) orienting the dowel hole towards the centre of the staircase.
2. Assemble the parts BE3, CC5, CC6 onto the baluster (C07) (fig. A).
3. Carefully measure the height from floor to floor to determine the number of spacer rings D03 (TAB. 2).
4. Assemble the spacers (D14, D03 and D02) as a single piece. Assemble the spacers (D04, D03 and D02) in the
same way.
Assembly
5. Determine the fixing point of the base G03 resting the landing E03 overturned on the floor. Mark the centre of
the spacer cup (fig. 3).
6. Use element G03 as a reference for the 3 floor fixing holes to perform using a Ø 14 mm bit.
7. Assemble the base (G03+B17+B46) (fig. 1).
8. Secure the base (G03+B17+B46) in a permanent manner to the floor with the elements B13 (fig. 1).
9. Tighten the tube G02 onto the base (G03+B17+B46) (fig. 1).
10. Insert the spacers (D14+D03+D02) (fig. 4).
11. Insert the base cover D05 - D12 (fig. 4).
12. Insert the first tread L02 into tube G02. Then, in this order, insert a spacer (D04+D03+D02) and the next tread
L02 and so on. Position the treads, alternating between right and left, so that the weight is evenly distributed
(fig. 4).
13. Once you have reached the end of the tube G02, tighten element B47, tighten the following tube G02 and
continue to assemble the staircase (fig. 4).
14. Once you have reached the end of the tube G02, tighten element B46 and element G01 (tighten element G01
taking into account the fact that it must be 15 cm taller than the height of the staircase) (fig. 5). Continue to
insert the treads using element D01 inserted in the spacer (D04+D03+D02) of the final treads L02 that are not
centred on column G02.
15. Insert the landing E03 last. Insert elements B05, B04 and secure element B03 sufficiently, considering that the
treads must still rotate (fig. 1).
Fixing the landing
16. Drill using a Ø 14 mm bit in correspondence with the holes present on the fixing flange to the floor.
17. Permanently secure the element B13 (fig. 1).
To assemble the railing
18. Fan the treads L02 out after you have chosen the rotation direction (fig. 6). You can now climb the stairs.
19. Calculate the exact position of the Ø 9 mm hole to be made on the landing E03 using the measurement on the
treads L02 as a reference.
20. Adjust the first baluster C07 (H. 1190 mm) to the landing E03:
1) measure the rise between tread L02 and landing E03 and add 2.5 cm,
2) drill a hole in the landing E03 with a Ø 9 mm bit,
3) cut the end part of baluster C07,
4) assemble elements F01 using elements B44, B27 and B23,
5) insert the cut part of the baluster between the lower element F01 and the tread L02,
6) tighten elements C31 of the tread and the landing,
7) insert and fix with element C31 the remaining part of baluster C07 in the upper element F01 (fig. 1).
Position balusters C07 keeping the direction of the holes of element B53 towards the centre of the staircase
and in such a way that the countersink of the element remains towards the inside of the railing.
21. Then insert all the longer connecting balusters C07 (H. 1190 mm) between the treads L02. Only tighten the
lower element C31 of the tread (fig. 2).
22. Check that all the balusters C07 positioned are vertical. Take care during this operation, since it is very
important for assembling the stairs correctly.
23. Finally tighten the element B03 (fig. 6).
24. Permanently tighten the upper element C31 of the tread (fig. 2).
25. Check that the balusters C07 are vertical and correct this, if necessary, repeating the operations described in
points 21, 22 and 23.
26. Fasten element F01 to the floor next to the first baluster C07 drilling with a Ø 8 mm bit. Use elements B11, B12
6 - SZ
Publicidad
