Envirolite EVL6742B Instrucciones De Instalación

Please read carefully and save these instructions, as
you may need them at a later date.
GENERAL: All electrical connections must be in accordance with local
and National Electrical Code (N.E.C.) standards. If you are unfamiliar
with proper electrical wiring connections obtain the services of a
qualified electrician.
Suitable for "TYPE IC".
Suitable for use in enclosed recessed luminaires.
Remove the trim from the box and make sure that no parts are missing
by referencing the PARTS illustrations.
THIS RETROFIT ASSEMBLY IS ACCEPTED AS A COMPONENT OF
A LED LUMINAIRE WHERE
COMBINATION SHALL BE DETERMINED BY CSA OR CANADIAN
AUTHORITIES HAVING JURISDICTION.
__________________________________________
WARNING- RISK OF FIRE OR ELECTRIC SHOCK
FOR USE WITH HOUSING MODELS: INCANDESCENT HOUSINGS –
COMMERCIAL ELCETRIC C7IC, C7ICR, C7ICA, C7ICRA, C7, C7R,
C7S, HBR5000SIC; HALO H7ICT, H7RICT, H7ICAT, H7RICAT, H7T,
H7RT, H27ICT, H27T, H27RT, H750ICAT, H750RICAT; CORDELIA
HBR7LICAT, HBR7LICRAT; CAPRI CR1, CRR1; ELCO EL7ICA,
EL7RICA; JUNO IC22, IC22R; LITHONIA L7X, L7XR; THOMAS PS1,
PS1-RM; DMF DH6ICATQ, DH6ICRATQ; NORA NHIC-17QAT, NHRIC-
17QAT; ELITE B6IC, B6RIC; SEA GULL 11018, 11028. HALO LED
HOUSINGS – H750ICAT, H750RICAT.
•
Do not alter, relocate, or remove wiring, lampholders, power supply,
or any other electrical component.
assembly requires a person familiar with the construction and
operation of the luminaire's electrical system and the hazard
involved. If not qualified, do not attempt installation. Contact a
qualified electrician.
•
Do not make or alter any open holes in an enclosure of wiring or
electrical components during kit installation.
•
To prevent wiring damage or abrasion, do not expose wiring to
edges of sheet metal or other sharp objects.
____________________________
ASSEMBLY AND INSTALLATION
1. If the installed housing does not have TORSION SPRING SLOTS or
C-CLIPS (FIG. 3), then remove the SCREWS securing the
TORSION SPRINGS to the HEATSINK. Attach the FRICTION
BLADES (included) to the same location using the SCREWS that
were previously removed. (FIG. 6)
INCANDESCENT HOUSINGS
1. Unscrew the WING NUT inside the CAN to detach the SOCKET
BRACKET from the CAN. Disengage the SOCKET from the
SOCKET BRACKET. (FIG. 2)
2. Thread the SOCKET ADAPTER into the SOCKET. (FIG. 3)
3. Plug the FEMALE CONNECTOR of the RETROFIT TRIM onto the
MALE CONNECTOR of the SOCKET ADAPTER ASSEMBLY. (FIG.
4)
4. If using TORSION SPRINGS, squeeze both TORSION SPRING
arms together and insert into the TORSION SPRING SLOTS (or
RECEIVER BRACKETS) of the CAN. (FIG. 5)
5. Tuck all wires into the CAN and carefully push the RETROFIT TRIM
into CAN. (NOTE: To provide enough room in shallow cans, carefully
position SOCKET ADAPTER and SOCKET adjacent to the long side
of the LED DRIVER prior to inserting the RETROFIT TRIM into the
CAN.) (FIG. 5)
LED HOUSINGS
1. Plug the FEMALE CONNECTOR of the RETROFIT TRIM onto the
MALE CONNECTOR of the HALO HOUSING. (FIG. 4)
2. If using TORSION SPRINGS, squeeze both TORSION SPRING
arms together and insert into the TORSION SPRING SLOTS (or
RECEIVER BRACKETS) of the CAN. (FIG. 5)
LED 6" RETROFIT TRIM
INSTALLATION INSTRUCTIONS
MODEL EVL6742B
THE SUITABILITY OF
Installation of the retrofit
ALL RIGHTS RESERVED  ENVIROLITE 2018
WARNING - RISK OF ELECTRIC SHOCK.
DISCONNECT MAIN POWER AT FUSE OR CIRCUIT
BREAKER BEFORE INSTALLING OR SERVICING
PARTS
SOCKET ADAPTER ASSEMBLY
THE
RETROFIT TRIM
FIG. 4
FIG. 6
QUESTIONS? CALL TOLL
1-855-573-6156
FREE
THE FIXTURE.
COMPATIBLE
HOUSING DIMENSIONS
FIG. 2
6 in.
FIG. 1
FIG. 3
FIG. 5
REV 13-NOV-18