Klark Teknik DN32-DANTE Guia De Inicio Rapido página 12

22 KLARK TEKNIK DN32-DANTE
Specifi cations
Connectors
RJ45, Gigabit Ethernet 1 GBit/s,
'PRIMARY' and 'SECONDARY'
Input/Output Characteristics
Input / Output channels
Sample rates
Sample word length
Clock synchronisation, onboard high-quality
Dante network clock, based upon IEEE1588
PTP (precision time control)
System audio latency depends on Dante Controller
network confi guration
Dual-input Gigabit Ethernet ports
Indicator
Ethernet Link, LED indicator in socket,
fl ashes with network activity
1 Gbit/s Ethernet Link, LED indicator in socket
System Requirements
PC Hardware, minimum
Wired Ethernet interface
Windows applications, *recommended
(ASIO and WDM audio device interface)
Mac OSX applications
(Intel CPU only, no PPC support, CoreAudio)
Audinate is a registered trademark of Audinate Pty Ltd. Dante is a trademark of Audinate Pty Ltd. Mac is a trademark of Apple Inc. Windows is a registered trademark of
Microsoft Corporation in the United States in other countries. All other trademarks are the property of their respective owners. Audinate products are protected by one or
more of US Patents 7747725, 8005939, 7978696, 8171152 and other patents pending or issued, see www.audinate.com/patents.
2
32 / 32
44.1 kHz / 48 kHz
24-Bit PCM
Console 'Local'
or
Dante network clock 'DN32-DANTE'
0.25 ms, 0.5 ms,
1 ms or 5 ms
Ethernet Switch Mode or
Dante Redundancy Mode
2 LED, green
2 LED, amber
Dante Controller App Dante Virtual Soundcard
CPU Dual Core
CPU 1 GHz RAM 1 GB
RAM 512 MB Wired Ethernet interface,
Display 1024 x 768 1 GB/s required for channel
counts higher than 32 x 32
@ 48 kHz
XP SP3 32-Bit
Win7 32-/64-Bit
*Win7 32-/64-Bit
Win8 32-/64-Bit
Win8 32-/64-Bit
Mac OSX 10.6.8, Mac OSX 10.5, 10.6.8,
10.7.5, 10.8, 10.9 10.7.5, 10.8, 10.9
FEDERAL COMMUNICATIONS
COMMISSION COMPLIANCE
INFORMATION
KLARK TEKNIK
DN32-DANTE
MUSIC Group Research
Responsible Party Name:
UK Limited
Address: Klark Industrial Park,
Walter Nash Road,
Kidderminster.
Worcestershire. DY11 7HJ.
England.
Phone Number: +44 1562 741515
DN32-DANTE
This equipment complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
ClassB digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• •
Reorient or relocate the receiving antenna.
• •
Increase the separation between the equipment and receiver.
• •
Connect the equipment into an outlet on a circuit diff erent from that to
which the receiver is connected.
• •
Consult the dealer or an experienced radio/TV technician for help.
Important information:
Changes or modifi cations to the equipment not expressly approved by
MUSIC Group can void the user's authority to use the equipment.
Quick Start Guide 23