Program Mode - EQUATION BH-1401E Instrucciones Legales Y De Seguridad

4. INSTRUCTION FOR USE
Push the ON/OFF (0/I) button located at the back of the appliance to switch on the appliance.
Push again, if you want to switch o .
Set date and time:
The date and time setting can be done only when the appliance is in standby mode.
Press SET, the day icon 1 2 3 4 5
Then press OK, the hour icon
minute icon ashes. Use + and – to set minute. In the end, press OK to con rm and
nish day and time setting.
Switch mode:
Press once to switch mode:
- OFF/OFF shows under the day icon = manual mode;
- shows and in the same time, wake up time shows under the day icon = program mode.
Manual mode:
Press
- start at 2000W (show on screen.).
- Press once, the heater will run with 1000W power (shows
- Press for the second time, the heater will run in the fan mode (
- Press for the third time, the appliance will run with 2000W power in cycle.
- Press twice, the appliance will stop in 15 seconds.
- When the appliance is running, press SET, the icon of the temperature SET ashes. Use + and –
to set the target temperature. Press OK to con rm and nishtemperature setting.
Note:
1.The temperature SET should be higher than the room temperature (the
EN
temperature icon on the left). Otherwise, the appliance will not start heating.
2.One the room temperature achieves the target temperature, the appliance will
stop automatically.
3.If the room temperature is 3°C less than temperature SET, the appliance will
restart.

Program mode:

Set wake up time and temperature:
In standby mode, long press for 3 seconds,
you are setting the wake up time and temperature for week-days.
6 7 ashes. Use + and - to set current day.
ashes. Use + and – to set hour. Then press OK, the
on the screen.).
shows on the screen.).
ashes. This means that
1 2 3 4 5
58
The hour icon under
1 2 3 4 5
the minute icon ashes. Use + and – to set minute. Then, press OK to con rm the
wake up time for week-days and the temperature SET ashes. Use + and – to set target wake
up temperature.
(During the setting, you can press SET to activate/shut down the wake up program for
week-days.)
Then press OK to move on to wake up time and temperature setting for week-ends.
ashes. This means that you are setting the wake up time and temperature for week-ends.
In the same way, you can set the wake up time and temperature for week-ends.
(During the setting, you can press SET to activate/shut down the wake up program for
week-ends.)
In the end, press OK to con rm and end the setting. All icons will stop ashing.
Note:
1.In program mode, the heater starts working at wake-up time for 15 minutes. If no
presence of people is detected by the sensor located at the front of the appliance,
the appliance will stop heating. If the presence of people is detected, the heater will
keep working for an extra 15 minutes.
2.In program mode, the heater can only run with 2000W.
3.In program mode, when working, the setting wake-up timeflashes and the icon
not shown at the screen.
Towel heating:
When the hanger is unfolded, press button
the screen. Press again to stop towel heating, or the towel will stop automatically after
two hours if you don't turn it o manually, and icon
(The towel heating cannot be turned on if the hanger is folded up, and icon
the screen.)
Note: The maximum weightbearing for towel should less than 2kg/bar(6 kg in total
for 3 bars)
Filter clean:
Filter becomes dirty during use, or after 30 hours usage, the indication
sounds "BE, BE, BE...". Press OK, sounds stop while
remove the lter on the back of the appliance. Clean the lter directly under water. Do not use
caustic or abrasive material during cleaning, as this can damage the lter. Then, have the lter
dried naturally.
The machine can'twork until disappear, which will take around 15 minutes.
Then reassemble the lter according to the reference line.
ashes. Use + and – to set hour. Press OK,
6 7
to start towel heating, and icon shows at
disappear at the screen.
disappear at
ashes with
ash. Turn the appliance o , then
59
EN