Bayco SL-1512 Manual De Instrucciones

Instruction Manual
SL-1512
THANK YOU FOR PURCHASING THE SL-1512 LED WORK LIGHT.
SAVE THESE INSTRUCTIONS.
PLEASE READ THESE INSTRUCTIONS BEFORE USING YOUR WORK LIGHT.
WARNINGS
IMPORTANT SAFETY INSTRUCTIONS
WARNING: READ ALL INSTRUCTIONS CAREFULLY
SAVE THESE INSTRUCTIONS
WARNING: When using outdoor lights, basic safety precautions should always be
followed to reduce the risk of fi re, electrical shock, and personal injury, including
the following:
Not intended for use in wet areas.
DO NOT use with extension cord near water or where water may accumulate.
Keep plugs and receptacles dry.
For use only on GFCI protected circuits.
Use only three-wire outdoor extension cords 16 AWG or larger that have three-prong
grounding plug and receptacles that accept the appliance's plug.
DO NOT use this work light with a 2 wire extension cord
Use only three-wire extension cords rated for outdoor use, such as an extension
cord of cord type SEW, SEOW, SEEOW, SEOOW, SOW, SOOW, STW, STW, STOW,
STOW, STOOW, SJEW, SJEOW, SJW, SJW, SJOW, SJOOW, SJTW, SJTOW, OR
SJTOOW.
SAVE THESE INSTRUCTIONS
Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • 1-469-326-9400 • www.mybayco.com
SAFETY INSTRUCTIONS
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK,
(EXPOSURE TO EXCESSIVE UV RADIATION,) OR INJURY TO PERSONS
WARNING: To reduce the risk of FIRE, ELECTRIC SHOCK OR INJURY TO
PERSONS:
Lighted lamp may become hot!
Light can be used indoor and outdoor.
Check that the sealed push button switch is in the off position before plugging in the
work light
Connect light to 120Volt, 60 Hz power source only.
Do not touch hot lens, or enclosure.
Do not remain in light if skin feels warm.
Do not look directly at lighted lamp, or direct the light at other persons.
Keep lamp away from fl ammable materials.
ASSEMBLY - PLEASE REFER TO THE ILLUSTRATIONS
OPERATION
The SL-1512 has a single sealed push button switch located on the back of the light
head.
Turning the light on:
Press and release the button.
Turning the light off:
Press and release the button.
WARRANTY
1 YEAR LIMITED WARRANTY
Bayco Products, Inc. warrants this product to be free from defects in workmanship
and materials to the original purchaser for one (1) year from the date of purchase, and
includes the LEDs, housing, lenses, electronics, switches, rechargeable batteries and
chargers. Bulbs (other than LEDs) are covered for ninety (90) days from the date of
purchase. Disposable non-rechargeable batteries are excluded from this warranty.
Normal wear and failures which are caused by accidents, misuse, abuse, faulty
installation and lightning damage are also excluded.
Consequential damages, incidental damages or incidental expenses, including
damage to property are also not covered under this warranty. Some states do not
allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. This warranty gives you specifi c legal rights,
which may vary from state to state.
IN NO EVENT WILL BAYCO PRODUCTS, INC. OR ITS AFFILIATES OR
SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF ANY KIND REGARDLESS OF THE FORM OF
ACTION, WHETHER IN CONTRACT, TORT (INCLUDING NEGLIGENCE), STRICT
LIABILITY OR OTHERWISE. THE TOTAL CUMULATIVE LIABILITY TO CUSTOMER,
FROM ALL CAUSES OF ACTION AND ALL THEORIES OF LIABILITY, WILL BE
LIMITED TO AND WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT
PAID BY CUSTOMER.
If this product is used for rental purposes, the warranty term is reduced to 90 days
from the date of purchase.
WARRANTY CLAIMS – USA
Return the product to the place of purchase for all warranty related issues. If this is
not possible, contact Bayco Customer Service at (800) 233-2155 M-F 8-5 Central Time
for a Return Goods Authorization (RGA). Do not return this product to Bayco without fi rst
receiving an RGA Number from Bayco Customer Service. When returning the product,
the RGA Number must be written on the outside of the shipping box.
WARRANTY CLAIMS – OUTSIDE OF USA
Return the product to the place where purchased for all warranty related issues.
INS-SL1512-15
INSTALLING THE LIGHT HEAD
Align the center hole in the
bracket of the Light Head with the
center hole in the Light Stand.
Using the included thumb
screw, tighten until fi nger tight.
CAUTION: Do not use any
tools to tighten the thumb
screw. Finger tight is all that is
required. Overtightening may
cause damage to the unit.