Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Instruction Manual
THANK YOU FOR PURCHASING THE SL-1530 LED WORK LIGHT.
SAVE THESE INSTRUCTIONS.
PLEASE READ THESE INSTRUCTIONS BEFORE USING YOUR WORK LIGHT.
WARNINGS
IMPORTANT SAFETY INSTRUCTIONS
WARNING: READ ALL INSTRUCTIONS CAREFULLY
SAVE THESE INSTRUCTIONS
WARNING: When using outdoor lights, basic safety precautions should always be
followed to reduce the risk of fi re, electrical shock, and personal injury, including the
following:
y Not intended for use in wet areas.
y DO NOT use with extension cord near water or where water may accumulate.
y Keep plugs and receptacles dry.
y For use only on GFCI protected circuits.
y Use only three-wire outdoor extension cords 16 AWG or larger that have three-prong
grounding plug and receptacles that accept the appliance's plug.
y DO NOT use this work light with a 2 wire extension cord
y Use only three-wire extension cords rated for outdoor use, such as an extension cord
of cord type SEW, SEOW, SEEOW, SEOOW, SOW, SOOW, STW, STW, STOW, STOW,
STOOW, SJEW, SJEOW, SJW, SJW, SJOW, SJOOW, SJTW, SJTOW, OR SJTOOW.
SAVE THESE INSTRUCTIONS
Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • 1-469-326-9400 • www.baycoproducts.com
SL-1530
SAFETY INSTRUCTIONS
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, (EXPOSURE
TO EXCESSIVE UV RADIATION,) OR INJURY TO PERSONS
WARNING: To reduce the risk of FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS:
y Lighted lamp may become hot!
y Light can be used indoor and outdoor.
y Check that the sealed push button switch is in the off position before plugging in the
work light
y Connect light to 120Volt, 60 Hz power source only.
y Do not touch hot lens, or enclosure.
y Do not remain in light if skin feels warm.
y Do not look directly at lighted lamp, or direct the light at other persons.
y Keep lamp away from fl ammable materials.
ASSEMBLY - PLEASE REFER TO THE ILLUSTRATIONS
SETTING UP THE WORK LIGHT
OPENING THE TRIPOD LEG SET
y Fully unfold the Tripod Leg Set and slide the Center Collar down until it locks into place.
WARNING: Do NOT attempt to use the Tripod Leg Set unless the legs are fully
extended and locked into place. This is the ONLY position that the leg set can be
used in.
CLOSING THE TRIPOD LEG SET
y Press the RED Release Button on the side of the Center Collar and then raise the Center
Collar up until the Tripod Let Set is fully retracted.
ADJUSTING THE COLUMN SECTIONS
y The tripod has two adjustable sections of the column that can be used to customize the
working height of the Work Light. Each section is locked into place by means of a Cam
Lock Lever. To adjust the height of either section, release the Cam Lock Lever for that
section, extend the column to the desired length and the re-lock the Cam Lock Lever.
REMOVING THE CONVERTIBLE LIGHT HEAD FROM THE TRIPOD
y The SL-1530 is designed so that the entire Light Head can be removed from the tripod.
To remove the Light Head, grasp the Padded Light Handle with one hand, squeeze
together the Light Head Release Clip Tabs and pull up on the Padded Light Handle.
INSTALLING THE CONVERTIBLE LIGHT HEAD ON TO THE TRIPOD
CAUTION: Before installing the Light Head on to the Tripod, be certain that the Leg
Set is fully extended and locked in place and that both of the two column Cam Lock
Levers are securely locked.
y To install the Light Head on to the Tripod, simply line up the Locking Alignment Pin on the
bottom of the Light Head Stand with the hole in the top of the Tripod Column. Then simply
press down until the Light Head locks into place. Be certain that the Light Head is locked
into the Tripod Column before letting go of the Light Head.
INS-SL-1530-20
INSTALLING THE CARRY HANDLE
y Using a #2 Phillips Screwdriver and the 2 included
short screws, attach the Carry Handle to the Light
Stand.
CAUTION: Hand-tighten only. Do not overtighten or
use an electric or battery-powered Drill Driver. Doing
so may cause damage to the unit or the screws.
INSTALLING THE LIGHT HEADS
y Align the center hole in the bracket of each of the
Light Heads with the corresponding hole in the Light
Stand.
y Using the included thumb screws, tighten until fi nger
tight. Do this for both Light Heads.
CAUTION:
Do not use any tools to tighten the
thumb screw. Finger tight is all that is required.
Overtightening may cause damage to the unit.
INSTALLING THE "Y" SPLITTER
y Using a #2 Phillips Screwdriver and the included
long screw, attach the "Y" Splitter on the Power Cord
to the back of the Carry Handle.
CAUTION: Hand-tighten only. Do not overtighten or
use an electric or battery-powered Drill Driver. Doing
so may cause damage to the unit or the screw.

Publicidad

loading

Resumen de contenidos para Bayco SL-1530

  • Página 1 REMOVING THE CONVERTIBLE LIGHT HEAD FROM THE TRIPOD y DO NOT use with extension cord near water or where water may accumulate. y The SL-1530 is designed so that the entire Light Head can be removed from the tripod. y Keep plugs and receptacles dry.
  • Página 2 ENLEVER LA TÊTE DE LAMPE CONVERTIBLE DU TRÉPIED AVERTISSEMENTS y La lampe SL-1530 est conçue pour que la tête de la lampe puisse être retirée du trépied. DIRECTIVES DE SÉCURITÉ IMPORTANTES Pour retirer la tête de la lampe, saisir la poignée rembourrée de la lampe avec une main, AVERTISSEMENT : LIRE ATTENTIVEMENT TOUTES LES DIRECTIVES presser ensemble l’attache de relâchement de la tête de la lampe tout en soulevant sur la...
  • Página 3 EXTRACCIÓN DE LA LÁMPARA DE CABEZA CONVERTIBLE DEL TRÍPODE INSTRUCCIONES DE SEGURIDAD IMPORTANTES y La SL-1530 está diseñada de modo que toda la Lámpara de Cabeza se pueda quitar del trípode. Para quitar la Lámpara de Cabeza, tome el Mango Acolchado de la Lámpara con ADVERTENCIA: LEA CUIDADOSAMENTE TODAS LAS INSTRUCCIONES una mano, apriete juntas las pestañas de liberación de la Lámpara de Cabeza y tire hacia...