Pyronix PCX-PROX/IT Guia De Inicio Rapido

Flushmount Proximity Reader
Partcode: PCX-PROX/IT
Document SAP
102018713
EN50131-1:2006+A1:2009
Environmental Class II
EN
Dimensions and weight
Please see graphic for dimensions and weight of product.
1-3. Installation
Please follow steps 1-3 for installation of the product into an RJ45 faceplate. After
step 3 the product is ready to screw into the backbox (not included).
4. RS485 wiring
Section 4 shows how to connect the RS485 bus into the proximity reader.
Please note: The colours used are for reference and not essential to the reader
working.
5. Addressing
Using the table in section 5 as a guide, set switches labelled 1, 2, 4, 8 and 16 to
the address required. The reader can be addressed from 01 - 31.
6. LED indications
Section 6 shows the LED sequences for the follows scenarios.
i. Powering up iv. Setting/arming
ii. 485 BUS fail v. Set/armed or
iii. Day mode (unset) Engineer Mode
7. Alarm input wiring
To wire an EOL input to the device, make sure switch A is on and that B and C are
off. Regardless of the EOL setting on the panel, the input must be wired using
DEOL 1k/1k configuration. Please refer to the input's installation guide for wiring.
8. Tamper input wiring
To wire a tamper circuit as normally closed to the device, make sure switch A and
B are on and that C is off. For a normally open circuit, A and C need to be on and
B needs to be off.
9. Output wiring
In order to use the 'Z' terminal as an output, switches B and C need to be on and
switch A needs to be off. The example shown is for access control however it can
be programmed as any type of output. Please refer to the control panel guide for
programming.
On Off
Please note: Current drawn must not exceed 100mA
Specifications
Device colour Operating voltage
Translucent Black ~9-16VDC
Casing Current consumption
Plastic <120mA maximum
LED colours Storage temperature
Green, red, yellow and blue -
40°C to +80°C
Tamper switches
Operating temperature
Externally wired to device
-10°C to +40°C
Product information
Applies to electrical products sold within the European community. At the end
of the electrical product's life, do not dispose of it with household waste. Where
possible, recycle the product. Check with your Local Authority or retailer for
recycling advice in your country.
Warranty
This product is sold subject to our standard warranty conditions and is
warranted against defects in workmanship for a period of five years. In the
interest of continuing care and design, Pyronix Ltd reserves the right to amend
specifications without giving prior notice.
 0845 6434 999 (UK) .+44(0)333 444 1280
55mm
32mm
4
Control Panel
- + D3 D4
vi. Tamper
vii. Active fault/alarm
silenced
D1 D2 D3 D4 Z Com
6
i
ii
iii
iv
v
vi
vii
 customer.support@pyronix.com
1
17mm
48mm
28.5g
19mm
5
1 2 4 8 16 A B C
7
N/C N/C
Powering up
MASK ALARM
485 BUS fail
Day mode (unset)
Setting/arming
Set/armed or
Engineer Mode D1 D2 D3 D4 Z Com
Tamper
1 2 4 8 16 A B C
Active fault/alarm silenced
 www.pyronix.com
2
Switch
1 2 4 8 16
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
8
N/C N/C
TAMPER
TAMPER
D1 D2 D3 D4 Z Com
N/C
1 2 4 8 16 A B C
N/O
1 2 4 8 16 A B C
Pyronix Limited, Pyronix House, Braithwell Way, Hellaby, Rotherham, S66 8QY, UK
3
Switch
1 2 4 8 16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
9
+ -
-
+
N/C
COM
N/O
D1 D2 D3 D4 Z Com
1 2 4 8 16 A B C